Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

An LG gas stove burner that won't shut off is usually a stuck gas valve or a worn control knob. What each cause looks like, how to make the range safe immediately, and when a valve needs professional replacement.

An LG microwave that keeps running is most often a stuck control-board relay or a stuck door switch. Ranked causes, why it matters to unplug it, and safe checks before replacing the switch or board.

Most likely the dryer is not level or you are drying a single heavy item that unbalances the drum. On these LG DLEX front-loaders those two easy causes lead; after them come worn rear drum rollers, a stretched drive belt, and loose internal hardware. A stacked, unlevel washer underneath amplifies it all. Start by leveling all four legs.

Most likely: the door isn't registering closed (a "dE" code) or Start wasn't pressed and held — LG requires a 1-2 second hold, not a tap. If the panel is dark instead, check both legs of the 240V supply and the thermal fuse. Whether the display lights tells you where to look…

An LG dryer that hums but won't turn the drum is most often a broken drive belt or a failed idler pulley, sometimes seized drum rollers, a bad motor, or a door switch not registering. The causes ranked for DLEX and DLE models, with the Smart Diagnosis tip.

LG dryer makes noise? Top 4 causes ranked by likelihood with step-by-step fixes. Learn about common problems, estimated repair costs, and when to call a...

LG dryer not heating? A restricted vent is the top cause, then a blown thermal fuse, a burned-out element on DLEX models, or a weak igniter on DLGX gas dryers. Ranked causes and how to test each.

LG dryer codes point straight at the failed part or condition. Here is what dE, tE and the heater codes mean, how FlowSense works, and how to clear each fault.

Complete guide to LG standalone freezer error codes for upright and chest models. Covers temperature sensor faults, defrost errors, compressor issues, and step-by-step repairs with LG part numbers.
Microwave completely dead or not responding? Diagnose blown fuse, faulty door switch, and control board issues with repair costs and safety warnings.
Oven door locked shut after self-clean? Learn why the door lock mechanism sticks, how to safely release it, and when you need professional repair.

An LG dishwasher door latch holds the door and signals the board via two micro-switches. No-start is the primary switch, start-then-stop is the safety switch. EasyBear guide.

LG dishwasher lights flashing or blinking? Rule out power quality and water supply first, decode the LED pattern, and see which faults need a technician.

LG dishwasher leaving dishes dirty? Diagnose QuadWash spray arm, water temperature, and detergent issues on LG LDP, LDT, and Studio series. Learn about...

LG dishwasher leaving dishes wet? Diagnose rinse aid, heating element, and vent fan issues on LG QuadWash and TrueSteam models. Expert repair guide by EasyBear.

Where it stopped narrows the cause. What it feels like in the first ten minutes narrows it further — tub heat, standing water and whether it restarts at once or only after an hour are evidence that disappears while you look for a manual.

Detergent cup remaining closed on your LG dishwasher? Step-by-step diagnosis of the wax motor actuator, dispenser latch, and control board timing on LDT/LDP...

A dead KitchenAid refrigerator is an electrical diagnosis, not a cooling one. The six causes by frequency, and the order to check them so you do not replace a good board.

An LG dishwasher tripping the breaker is leaking current — a standard-breaker trip points at a grounded heater or pump, a GFCI trip points at moisture. Identify the device, then isolate the part.

A burning smell from an LG dishwasher usually starts at the Inverter Direct Drive motor, the heating element, or the control board. The smell itself tells you where to look.

An LG dishwasher that stalls before finishing usually has a fouled turbidity sensor or a blocked drain pump. Read the stage it stops at to find the fault fast.

LG's Dynamic Dry uses residual heat, a fan, and an auto-cracking door instead of a heated element — so wet plastics are normal, but all-wet dishes mean the door actuator failed.

LG dishwasher not filling? Diagnose the water inlet valve (5220FR2006H), supply pressure, and float switch specific to LDT/LDP models with error code IE.

LG dishwasher display blank or unresponsive? Diagnose control board, ribbon cable, and power supply issues specific to LDT and LDP series models.

LG dryer cycle not completing? Top 8 causes ranked by likelihood with step-by-step fixes. Learn about common problems, estimated repair costs.

Most likely: the wax motor actuator has failed. LG's dispenser (on LDT and LDP models) uses a wax motor, not a solenoid — the control board sends it 120V, its internal heater melts a wax pellet over thirty to forty-five seconds, and the expanding plunger releases the cup latch so the spring-loaded…

Most likely: the tub-floor heating element has burned out — it is behind nearly half of HE errors — or the thermistor is feeding the board a false "hot" reading so it never fires the element. One LG-specific point saves confusion: this element heats the wash and rinse water only; it does not dry…

Most likely: the door latch micro-switch has failed, or Child Lock is switched on. LG's latch carries an integrated micro-switch (4027ED3001 on most models) that must tell the board the door is shut; its plastic actuator wears out, so the door latches mechanically but the switch never signals. The…

Most likely: the noise ties to one cycle phase — a fluttering inlet valve during fill, a worn Inverter Direct Drive motor or spray arm during wash, or a failing drain pump during drain. Match the sound to the phase to find the part, since LG builds these for a low LoDecibel baseline.

Most likely: it splits three ways. A completely dead LG dishwasher has lost power (breaker, GFCI, or a blown onboard board fuse). A lit panel that ignores Start is usually the door latch not confirming, or Child Lock. A unit that clicks then stops points at the door switch or a locked motor.
Let our professional technicians help. Same-day service available.