Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

GE washer shaking hard or walking on spin? It’s an imbalance — leveling, worn shock absorbers, suspension rods, or a cracked spider arm. Ranked causes and DIY checks for GFW and GTW washers.

Whirlpool dryer not heating? Diagnose and fix the 7 most common causes, from blown thermal fuses to bad heating elements. Step-by-step repair guide.

Two identical faults can be quoted very differently, and the reasons are knowable before the technician arrives. A table of what moves the number — machine type, brand, access, and which part failed.
Washer repair costs in California range from $80 to $450. Get a full 2026 breakdown by issue type — bearings, pumps, boards — plus top-load vs front-load.

GE refrigerator smells like burning? Treat it as an electrical fault — usually a compressor relay, condenser fan motor, or wiring. Here's the safe response.

GE refrigerator display blank or partial? Work power to dispenser board to door communication in order — a reset clears many blank displays before any part.

A misaligned GE refrigerator door breaks the gasket seal and causes condensation. Usually an adjustment, not a part — level the cabinet, then fix the sag. EasyBear guide.

GE refrigerator freezing food in the fresh food section? Diagnose damper, thermistor, and board issues on GE Profile, Cafe, and standard models.

GE refrigerator running too long? Causes and fixes for extended compressor cycles on GE models. Learn about common problems, estimated repair costs.

GE refrigerator not making ice? It comes down to two questions: is water reaching the ice maker, and is the freezer cold enough? Here's the full diagnostic.

Rust or corrosion on your GE refrigerator? Guide covering door handle rust on GFE/GNE French doors, evaporator coil corrosion, condenser panel rust.

GE refrigerator temperature off? Whether it's too warm or too cold, the cause is airflow, defrost, or a sensor. Here's the full diagnostic and what needs a pro.

GE washer stops mid-cycle? The single most useful clue is which stage it dies at — fill, wash, drain, or spin. Each stall point maps to a specific fault, from a clogged drain pump to an out-of-balance abort loop. Diagnose by stage.

A burning smell from a GE washer is usually the WH01X27540 belt slipping or a sheared GTW motor coupling — but a sharp electrical odor means board or wiring arcing, so unplug first.

GE oven keeps heating after you turn it off? A welded control relay, a stuck sensor reading, or a gas valve fault is behind it. Here's the safe step to take and what to check.

A GE refrigerator that never stops running is usually shedding heat poorly — dirty condenser coils, a dead fan, or a leaking door seal. Rule out normal long run times, then work the list.

A GE oven that won't start is a power or control-level fault, not a heating fault. The first split — dead panel vs lit panel — tells you exactly where to look.

Everyone says check the door switch. Almost nobody says how to be sure without a meter — the same switch also controls the evaporator fan, so what the fridge sounds like with the door open answers it in ten seconds.

The GE-specific trap first: the RPWFE filter's RFID chip can lock out all water flow. After that, check a frozen door line, the inlet valve, and the dispenser switch.

A GE refrigerator that vibrates or shakes is usually out-of-level legs, an imbalanced condenser fan, or loosened compressor mounts. Learn the normal vibrations to ignore, then use this ranked guide and DIY checks to quiet it.

A dead GE washer display is most often a ribbon-cable fault, a failed user-interface board, or lost power to the display circuit. A blank display doesn't always mean a dead machine. Here are the causes ranked, plus the checks to run before disassembly.

GE refrigerator not defrosting? Top causes ranked by likelihood with step-by-step fixes for GE models. Get expert diagnosis and repair costs.

GE washer door latch not working? Complete guide to lock mechanisms on GFW front-loaders (WH44X27819) and lid lock systems on GTW top-loaders.

A GE fridge sweating between the French doors is a failed mullion (anti-sweat) heater — or Energy Saver mode left on, which switches it off. Sweating at the edges usually means a worn gasket.

A GE fridge that trips the breaker is usually a failing compressor start relay, a nuisance-tripping GFCI, or a defrost heater grounding out. When it trips tells you which — and don't upsize the breaker.

A GE refrigerator running too cold usually means a drifting fresh-food thermistor or a damper stuck open flooding the fridge with freezer air. This guide ranks the causes, covers TwinChill fan and control-board faults, and shows the resets and checks to try first.

A GE refrigerator that won't start is most often a failed start relay or overload — if the lights work but the compressor doesn't run, the fault is in the compressor circuit. Ranked causes covering the board, compressor, thermostat, cord, and overload, with safe checks.

A noisy GE refrigerator is most often the ice maker or a failing condenser fan, then the evaporator fan or a clicking start relay. Ranked causes matched to the sound, safe checks, and when a fan or compressor needs service.

Most likely: the defrost heater has burned out — the only heat source in the fridge is the defrost heater that melts frost off the evaporator, and when it fails, ice buries the coil and cooling dies. A defrost thermostat failed open or a board relay are next. Run GE diagnostic Test 6 and watch for the orange glow…

A GE French-door refrigerator that won't stay shut usually lost its rear tilt, not a latch — plus binding freezer-drawer rails, a Profile door-in-door spring, a worn hinge cam washer, or a weak gasket. The causes ranked, with how GE doors actually close.
Let our professional technicians help. Same-day service available.