Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

Replacing the 240-volt wall receptacle a Whirlpool dryer plugs into means matching NEMA 14-30 (4-prong) or NEMA 10-30 (3-prong) and wiring the box safely. Electrical experience required.

Complete guide to LG induction cooktop error codes. Covers pan detection, temperature sensor, power module, and cooling fan errors with step-by-step fixes and LG part numbers.
Should you use surge protectors for appliances? Learn which California appliances need protection, what type to buy, and how power surges damage electronics.
Freezer repair guide — frost buildup, temperature failures, compressor issues, costs by repair type, and when replacement makes more sense in 2026.

Complete cleaning guide for Whirlpool dryers including lint trap deep-clean, internal duct vacuuming, AccuDry moisture sensor bar cleaning (sandpaper and...

Access a Whirlpool dishwasher's racks, spray arms, filters, inner door panel, and kick-plate area — no water lines or countertop screws removed. Covers the common W10350376 rack fix.

Pull a Whirlpool dishwasher out and fully disassemble it — kick plate, water and drain disconnection, countertop screws, inner door panel, control board, spray arms, filters, and pumps.

Safely disconnect and pull a built-in Whirlpool dishwasher — breaker and water shutoff, electrical and drain disconnection, countertop screws, and sliding it out on cardboard.

Troubleshoot and fix a Whirlpool dishwasher that won't drain. Covers clogged filter, drain hose blockage, pump testing, and F5E2/F8E1 error code solutions.

Remove your old Whirlpool dishwasher and install a new one. Covers electrical, plumbing connections, leveling, and first-run testing for WDT/WDF models.

A dishwasher has two pumps with different part numbers and they are not interchangeable. Dirty dishes point at one, standing water at the other, and shallow water at neither — sort that before you order anything.

Whirlpool dryer teardown in order: spring-clip top panel, front panel after the door switch, belt off the idler, drum out. Component map and belt routing included.

Before condemning the board on a WF-series front-loader, reseat every harness — a loose connector imitates board failure exactly. Then it is a 30 to 45 minute swap, photographs first.

PE or OE codes, water out of the detergent dispenser, or a drum that barely fills — the pressure switch or its air tube. Check the tube before you buy the switch.

When the detergent cup stays shut mid-cycle, the wax motor behind it has usually failed. Removing the inner door panel is the whole job — about 8 Torx T20 screws and 25 to 35 minutes.

The perimeter gasket on a WDT or WDF dishwasher is friction-fit — no screws, no glue, no adhesive. Pull the old one out, press the new one in from top centre, and work the corners without stretching.

Whirlpool grinds food rather than just trapping it, so the chopper, the dual filter, the three spray arms and the soil sensor lens all need attention. Allow 30-40 minutes.

Thumping in spin and a tub that sits visibly low means the upper suspension springs have stretched. Replace the straps as a set before the tub wears the base frame.

tE, tE1 and tE2 codes on a Samsung front-loader point at the temperature sensor in the tub wall. Meter it at room temperature before ordering the model-matched part.

Washes fine, dries nothing? Three parts sit in the Whirlpool heated dry circuit — board relay, thermal fuse and element. Test them in order before buying anything.

Samsung washer walking across the floor or throwing DC and UE codes? Separate load and levelling problems from worn shock absorbers DC66-00470A and a failed balance ring.

Fix a Samsung WA-series top-loader that will not start or stops mid-cycle by replacing the lid switch. Covers continuity testing, console access, and the Active WaterJet lid.

Clear a 5E drain error on a Samsung front-load washer by servicing the debris filter, freeing the drain-pump impeller (DC31-00054A), and flushing the drain hose.

Trace a Samsung washer drain failure from the easy clog checks to metering the DC31-00054A pump motor, so you confirm the fault before buying parts. Covers the 5E drain error.

Replace the clutch/brake assembly on Samsung WA-series top-load washers. Fixes spin cycle failures, grinding noises during transition from wash to spin.

Fix a leaking or non-dispensing rinse aid system on your Whirlpool dishwasher. Covers cap replacement, dosage adjustment, and dispenser body swap.

Replace the NTC thermistor in a Whirlpool dishwasher to fix F3E1 and F3E2 error codes. Locate the sensor in the sump, test with multimeter, and install new.

Fix an F6E1 no-fill on a Whirlpool dishwasher by replacing the inlet valve (W10872255). Covers the solenoid resistance test, kick-plate access, and a leak test.

Replace a failed heating element in a Whirlpool dishwasher that leaves dishes cool or throws F3E1/F3E2. Covers the resistance test, pulling the unit, the underside swap, and a heat test.

Replace the drain pump on your Whirlpool WDT/WDF dishwasher. Covers part W10876537, sump access, wiring, and testing for F5E2 drain errors.
Let our professional technicians help. Same-day service available.