Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

An LG fridge that won't start is either dead (power, cord, board) or powered-but-silent (Linear Compressor relay, inverter board, or seizure — check the Er CO code). EasyBear.

LG washer door latch failing? It either won't lock (so the cycle won't start) or won't release at the end. Here's how to tell which, and the safe fix.

LG washer rust is either serious spider-arm corrosion (structural) or cosmetic cabinet paint rust, drum staining, and boot-seal mildew. Tell them apart — EasyBear guide.

A dead LG washer display is usually a failed line filter or a board power fault, not the screen. Try Smart Diagnosis, rule out the outlet, then test the filter.

Maytag dishwasher lights flashing or blinking are fault codes in disguise. Count the blinks to read the F-E code, match it to our cheat sheet, and fix the real cause.

An LG washer keeps its door locked for good reasons — water in the tub, a spin cooldown, a power cut. Here is how to release it by situation, and when the wax-motor lock has failed.

A noisy Maytag dishwasher is usually a chopper-assembly obstruction, a worn wash-motor bearing, or a spray arm hitting something. Match the noise type and cycle timing to the cause with this ranked guide, plus when a noise signals urgent repair.

LG refrigerator tripping breaker? Diagnosis of compressor inrush current spikes, ground faults, defrost heater shorts, and inverter board failures causing...

LG washer overflowing or overfilling? Diagnose pressure switch failure, stuck inlet valve, and water level control issues on WM and WT series.

An LG washer that starts but never finishes is most often a blocked drain pump throwing OE. The phase where the cycle freezes points straight at the system at fault.

An LG washer that walks across the floor is most often shipping bolts never removed after install, then uneven leveling or worn shock absorbers. At 1,300 RPM, all three let it march.

A Maytag dishwasher shows a two-part F#-E# code: the F number names the failed system, the E number the exact fault. Here's what the common ones — fill, drain, door, and sensor — mean and how to clear them.

LG washer timer stuck or not counting down? Diagnose control board issues, adaptive cycle timing, and sensor-driven pauses on WM and WT series models.

Burning or electrical smell from your Maytag MDB dishwasher? Identify whether it's the motor, wiring harness, chopper assembly, or heating element with this...

An LG refrigerator that vibrates or shakes is most often unlevel, has hardened compressor mounts, or sits on a resonant floor. This guide ranks the causes behind Linear Compressor vibration and shows the leveling and isolation checks to try first.

An LG washer burning smell is usually a shorted stator winding — Direct Drive has no belt to slip, so the cause is electrical. Ranked causes covering the board, drain pump, arcing wiring, drum bearing, and first-use residue, plus the safety steps to take first.

An LG washer tripping the breaker usually means a stator shorted to ground, but a shorted heater or pump, a chafed harness, a bad line filter, the board, or an overloaded circuit can all be the cause. Trip-timing diagnosis and the safety rules that come first.

Most likely, if it always runs cold on a hot setting the cycle is a ColdWash program by design, or the hot supply is blocked. Not hot enough usually means the supply plus LG's blending. Too hot or swinging points to a leaking hot solenoid or a drifting thermistor, and a failed thermistor throws a tE code and defaults to cold.

Most likely a sensor is not giving the control board the signal it needs to move on, so a phase runs forever. On Maytag MDB dishwashers the top stall is a failed thermistor reporting a constant low temperature, so the board heats and waits for a target it never sees. A slow-heating element, a fouled turbidity sensor stuck in a rinse loop, or a weak drain pump are the others.

An LG washer collecting water while idle is usually a water inlet valve that won't fully close, sometimes drain-hose backflow from a standpipe issue or a pressure-switch air leak. How to tell clean supply water from siphoned drain water, and how to fix each.

The kind of noise a Maytag dishwasher makes points to the part — grinding is the chopper or motor bearings, humming without flow is the impeller, banging is the spray arm, and a squeal is a dry pump seal. A sound-by-type guide with the diagnostic mode.

Maytag MDB dishwasher door won't latch, pops open mid-cycle, or latch handle broken? Complete diagnosis and repair of the Maytag door latch assembly and...

Most likely: loose junction-box wiring or a control board fault behind a blank display, or a worn touchpad membrane behind unresponsive buttons. Diagnosis for the power path, LED driver, ribbon cable, and control lock on Maytag MDB dishwashers.

LG washer won’t start? Sort it by symptom: completely dead points to the line filter or board, display-on-but-no-start points to the door lock or Child Lock. Ranked causes and the CL/dE/LE codes.

LG washer won’t spin or only spins slowly? With the belt-free Direct Drive motor it’s usually an unbalanced load (UE), a failing hall sensor (LE/SE), a door lock, or undrained water. Ranked causes.

LG washer error codes are specific, so each points to a narrow set of parts. Here is the code-by-code reference with LG repair steps and the part behind each fault.

Because LG Direct Drive has no belt or gearbox, a loud LG washer usually means the tub bearing, spider arm, or shock absorbers. Here is the ranked noise fault tree.

Maytag MDB dishwasher leaking from the front, center, or side? Use the puddle location to isolate the gasket, pump boot, inlet valve, spray-arm seal, hinge seal, or float — ranked by frequency.

Complete guide to Midea dryer error codes. Decode E01–E08, understand heating failures, and learn DIY fixes. Covers electric and ventless heat pump models plus Comfee-branded dryers.

Complete guide to Viking refrigerator error codes for Professional, 5 Series, and 7 Series built-in models. Decode E1–E9 errors, understand causes, and learn when to call a certified technician.
Let our professional technicians help. Same-day service available.