Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

Bosch heat-pump dryers run cool on purpose. Real weak heat is usually a lint-clogged condenser, then a compressor or NTC sensor fault, or a burned element on WGA models.

A Bosch dryer not draining is usually a blocked pump impeller, a kinked drain hose, or a stuck tank float. E:08 vs E:18 tells you where to look. EasyBear repair guide.

Rust on your Bosch dryer? Guide to stainless drum staining, cabinet paint failure, condensate system corrosion, and moisture damage prevention on WTW/WGA...

A burning smell from a Bosch dryer is usually scorching lint on the heat exchanger or around the motor. Unplug, clear the lint, then check the belt and drum seal.

A Bosch dryer that runs but won't turn the drum has a broken drive belt in most cases. Turn the drum by hand — free means belt, bound means a seized pulley or roller.

A Bosch dryer that stops partway through a cycle is almost always a coated AutoDry sensor, a full condensate tank, or a heat-pump cutout. Here is how to tell which — ranked by likelihood — with the exact error codes and DIY checks.

Rust appearing inside your Bosch dishwasher? Identify rack tine corrosion, stainless tub staining, and iron-deposit issues specific to Bosch's European...

Bosch dryer showing error code? Complete reference for E:02 through E:23 on WTW/WGA series compact ventless dryers with causes, diagnosis steps.

Most likely: the under-sink supply valve is closed or the AquaStop safety valve is not opening. A clogged inlet screen, a failed inlet-valve solenoid (E03), or an E15 flood-protection lockout are the other causes. Bosch routes water through two valves — check them in order.

Most likely: a clogged condenser recirculating hot air instead of cooling it, or a failed NTC exhaust sensor reading low so the board keeps heating. A stuck thermal cutout or a welded element relay are the others. On a heat-pump Bosch, clothes should be warm — hot means regulation has failed.

Most likely, match the sound to the part: a steady rumble all cycle is the rear drum bearing, a startup squeal that fades is a glazed belt, a high whine when the drum turns is the tensioner-pulley bearing, and a rhythmic thump once per revolution is an object caught in the drum. On heat-pump models a low steady compressor hum is normal.

Most likely: a drifting NTC temperature sensor is making the flow-through heater quit early or run long, so your Bosch dishwasher leaves dishes cold or the water runs near-boiling. Rule out a lukewarm hot-water supply first — it needs no parts — then meter the NTC and the pump heater (BSH 00442548)…

Most likely: the machine isn't level — even a couple of millimeters lets the circulation pump's force rock it. Since Bosch dishwashers are among the quietest made, any real vibration means a leveling issue, hardened pump grommets, a worn spray-arm bearing, or debris in the drain pump…

Bosch dishwasher overfilling with water? Diagnose stuck inlet valves, float switch failure, and AquaStop E17 overfill protection on Bosch models.

Bosch dishwasher won't turn on or start a cycle? Troubleshoot door latch switches, control module faults, and power issues specific to Bosch SHX/SHP/SHV models.

Bosch dishwasher leaving the tab intact? A blocked dispenser door and a failed bi-metallic actuator top the list. Ranked causes and how to check each.

Bosch dishwasher tab still sealed after a cycle? The bi-metallic dispenser door didn’t open — usually a blocking dish or hardened residue, sometimes the actuator. Ranked causes and DIY fixes.

Bosch dishwasher empty after starting? The AquaStop dual-valve system means checking the supply valve, a kinked AquaStop hose, and an E15 flood trip first. Five-minute checks plus the E03 timeout.

Bosch compact dryer suddenly loud? Grinding means the drum bearing, a startup squeal means the belt, and a rattle means a loose part. How to identify each Bosch dryer noise and what it costs to fix.

Bosch dryer won’t spin? How the drum feels by hand tells you the cause: a free spin means a broken poly-V belt, normal resistance with no motor sound means the motor or board, seized means a tensioner.

Bosch compact dryer display blank, flickering, or partial? Diagnose the 240V power board, the display/control board, a loose ribbon cable, a blown internal fuse, or an active child lock.
Ice maker not making ice? Learn about frozen water lines, faulty ice maker assembly, water inlet valve problems, and temperature issues.

Troubleshoot the most common Kenmore refrigerator problems. Expert guide covering cooling issues, ice maker failures, noise, leaks, and more.

Troubleshoot every common KitchenAid dishwasher problem. Expert guide covering not cleaning, not draining, error codes, leaks, and noise issues.

Bertazzoni refrigerator freezing food? Expert diagnosis of common causes, model-specific fixes, and repair costs for Bertazzoni refrigerators.

Bertazzoni refrigerator ice maker stopped? Water valve, harvest motor, and control diagnostics for Bertazzoni Professional and Master series refrigerators.

Water pooling under your Bertazzoni refrigerator? Drain tube, door gasket, and defrost diagnostics for Bertazzoni Professional and Master series.

Bertazzoni refrigerator making noise? Expert diagnosis of common causes, model-specific fixes, and repair costs for Bertazzoni refrigerators.

Bertazzoni built-in refrigerator not cooling? Compressor, condenser fan, and control board diagnostics for Bertazzoni Professional and Master series.

Much Bosch cooktop noise is normal — induction hums, gas clicks at ignition. Real faults are continuous igniter clicking, a grinding fan, cracked glass, or loose mounting. EasyBear.
Let our professional technicians help. Same-day service available.