Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

A Bosch washer washing cold on a hot cycle most often has a burned-out heating element, then a misreading temperature sensor or a heater relay. Confirm it's a true hot cycle first.

A Bosch washer stuck on one temperature depends on the program: eco cycles heat internally, quick cycles use the hot supply. That split tells you whether it is the valve or the heater.

Bosch washer door won't lock or latch? Diagnose the bimetallic interlock, door striker, and wiring issues on Bosch 300/500/800 series compact front-loaders.

Burning smell from your Bosch washer? Diagnose motor inverter failures, door lock overheating, and pump seizures specific to Bosch EcoSilence Drive compact...

Most likely: a badly worn main drum bearing — when a Bosch bearing goes from merely noisy to genuinely loud, it has reached advanced failure, and at spin speed it becomes a roar you can hear across the house. A trapped foreign object (bra wire, coin, key) grinding between the drum and tub is the…

Most likely: the shipping transit bolts were never removed. Bosch locks the drum to the cabinet with three or four steel bolts (with red or yellow plastic spacers) for transport, and if they stay in, 100% of the drum's vibration transfers straight to the cabinet and the machine walks on every spin.…

Most likely: a scaled or failed heating element leaves water too cold, while a shorted NTC sensor reads false-low and runs the heater continuously, overheating it. A loose NTC connector makes it erratic. Some cool-feeling behavior is by design — confirm the actual temperature in diagnostic mode first.

A Bosch washer that won’t drain is a clogged drain filter or coin trap in nearly half of cases, then a failed drain pump or a blocked hose. Ranked causes, the filter you can clean yourself, and when the pump needs service.

Most likely the element is getting continuous power because a control-board relay welded shut, or the oven temperature sensor shorted and is commanding maximum heat. Either is a fire hazard — cut power at the breaker now. An E005 or E011 code helps point at the failing part. Here is how to diagnose it safely.

Most likely the leak location names the seal: water at the front below the door means the door boot gasket, water at the rear means the AquaStop supply hose, water underneath during drain means the drain-pump seal, and suds down the side mean detergent overdosing. Error E:23 means the base-pan sensor already caught a leak.

A Bosch oven running hot or cold is most often a drifted RTD sensor or a calibration offset that needs resetting, sometimes a partially failed element or a slowing convection fan. How to verify with an independent thermometer and work through each cause.

A Bosch washer that fills slowly or not at all usually has clogged inlet-valve screens or a triggered AquaStop hose, sometimes a failed inlet-valve solenoid, low water pressure, or a disconnected pressure-sensor hose. What E:02 means and how to work through it.

Bosch washer filling with water when turned off? Diagnose faulty inlet valves and AquaStop system failures on Bosch compact front-load washers.

Bosch washer drains normally but refuses to spin? Diagnose EcoSilence Drive inverter faults, door lock signals, and imbalance issues on Bosch compact...

Bosch washer showing an E code? What the water, drain, motor, and leak codes mean — E:18 is the most common — with the fix for each and how to clear them.

Bosch washer overflowing? The ranked fill-control causes led by a slipped pressure-sensor hose, what the E:23 AquaShield code means, and how to check each.

Bosch wall oven vibrating in convection mode? An unbalanced convection fan leads the list, followed by loose cabinet mounting, fan-to-plate contact, a loose rack, or worn SoftClose hinges.

Bosch 300/500/800 front-loader won’t spin? The EcoSilence Drive has no belt, so the failure modes differ — door lock, drain pump, inverter, spider, or pressure sensor. Ranked diagnosis inside.

Maytag washer won't spin or agitate? Learn the 7 most common causes and how to fix them. Covers Maytag Centennial, Bravos, and commercial models.

LG dryer not heating or drying clothes? Diagnose the 6 most common causes with our expert guide. Covers LG electric and gas dryer models.

A Bosch gas stove that clicks nonstop is a spark igniter misfiring — usually moisture or debris on the electrode, sometimes a stuck knob switch or spark module. EasyBear guide.

Bosch oven display blank? Unlike a small appliance, an oven runs on a 240V double-pole breaker — a half-tripped breaker is a classic blank-display cause.

The letter and first digit name the fault family. What the oven can still do — bake but run cool, refuse to heat, hold the door shut, or nothing at all — narrows that family to a part and tells you whether a second reset is worth trying.

Bosch gas burner won't light? Follow the ignition chain — spark, gas, flame sensor, hold — to find the break. A dry, clean igniter fixes most cases; a burner that lights then dies on release is the thermocouple. FlameSelect models are less forgiving of carbon buildup.

Bosch oven making noise? On a modern oven it's almost always a fan — the convection fan or the cooling fan. Here's how to tell which and what's normal.
Bosch gas stove burner won't light? Diagnosis of igniter failure, spark module faults, and gas valve issues with step-by-step troubleshooting.

A Bosch gas burner that keeps burning with the knob off is a stuck valve or a stripped knob shaft. Close the wall shutoff first; the repair is a valve replacement, not a cleaning.
Bosch gas stove or range smells like gas? Emergency diagnosis of gas leaks, faulty valves, and connection problems. Get expert diagnosis and repair costs.

Bosch gas stove producing uneven, yellow, or weak flames? Diagnosis of burner clogs, air shutter misalignment, and orifice problems. Repair guide with costs.

A Bosch oven element that won't heat is usually a burned-out element, a control-board relay, or a blown thermal fuse. Which mode fails tells you which element to test.
Let our professional technicians help. Same-day service available.