Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

Beko dishwasher won't start? Work the 60-second checks, then the four failure points by likelihood — plus the parts-sourcing wrinkle unique to this brand.

Beko refrigerator leaking water? The location of the puddle names the cause — under the crisper drawers means a clogged defrost drain, behind the unit means the supply line, and the front bottom means gasket condensation. Diagnose by where it pools.

Beko refrigerator not cooling? Expert diagnosis of common causes, model-specific fixes, and repair costs for Beko refrigerators. Book same-day repair.

Front, back, under the freezer or dead centre — on an Amana refrigerator the location of the water identifies the fault before you touch a screwdriver.

A Bertazzoni cooktop with weak, yellow, or lopsided flames is usually a clogged brass burner cap, wrong gas pressure, or the incorrect LP orifice. Here is how to tell which.

An Amana washer leak is diagnosed by location: front means the door boot, underneath means a hose, foamy means detergent, fill-only means the inlet valve. Trace it here.

A Beko dishwasher leak is usually the door gasket at the front, the inlet valve or a hose underneath, or oversudsing. Trace the location, then fix it.

A Beko dishwasher that leaves dishes dirty usually can't move hot water over them — clogged spray arms, a dirty filter, cool water, or weak detergent. Most fixes cost nothing.

An Amana washer that won't fill usually has a closed supply valve, a failed inlet valve, or a scaled inlet screen. Check the free stuff first — and remember Amana parts are Whirlpool parts.

A Beko washer that fills and agitates but won't spin has a spin-specific fault — most often the door lock, drive belt, or motor coupling. Here is how to rank them.

Amana washer making noise? Expert diagnosis of common causes, model-specific fixes, and repair costs for Amana washers. Book same-day repair.

An Amana washer left full of water is usually a clogged drain-pump filter (coin trap) catching debris — check it first — then a failed drain pump or a kinked drain hose. Here's the order to work through.

Amana washer won't start? Expert diagnosis of common causes, model-specific fixes, and repair costs for Amana washers. Book same-day repair.

Beko dryer not spinning? Expert diagnosis of common causes, model-specific fixes, and repair costs for Beko dryers. Book same-day repair. Expert tips and costs.

Beko washer won't start? Expert diagnosis of common causes, model-specific fixes, and repair costs for Beko washers. Book same-day repair. Causes, costs, fixes.

A Bertazzoni dishwasher that won't start is usually a door latch not closing both microswitches, a blown control-board fuse or varistor, a failed touchpad, or no incoming power. Model-aware diagnosis with the fast latch test and when to call a technician.

Most likely: a defective door switch, a blown thermal fuse, or a worn start switch. Confirm the outlet has power, the breaker is on, and the door closes firmly first. On Beko dryers the thermal fuse can sit in the control circuit, so a blown fuse leaves the machine completely dead.

A Beko dryer that tumbles but won’t heat is most often a blown thermal fuse, then a failed heating element or gas igniter. Ranked causes, why a blocked vent trips the fuse, and safe checks before a service call.

Most likely no power is reaching it, or the compressor's start relay has failed. If it is completely dead, test the outlet, check the breaker and GFCI, and inspect the cord. If power is confirmed but the compressor will not start, the start relay and overload on the compressor is the usual culprit, followed by a surge-damaged board or a tripped overload.

Most likely the drain-pump filter (coin trap) is clogged — Beko catches coins and lint before they reach the pump, and a packed filter stops drainage. After that: a failed drain-pump motor, a kinked or scum-clogged drain hose, or a lid switch or door lock that will not signal the board. Start at the coin trap, the free five-minute check.

Most likely the drain pump has failed or jammed, or the filter and sump are clogged with food debris. On these Italian-built units the other causes are a check valve stuck with scale, a kinked drain hose, or a control-board drain relay that no longer fires the pump. Standing water is the giveaway; parts are proprietary, so confirm the cause first.

Most likely: the washer isn't level — all four feet must sit firmly on the floor, and leveling alone fixes a large share of vibration complaints. An unbalanced load, worn shock absorbers, or a broken suspension spring are the other usual causes. Start with a bubble level…

Most likely: a failed compressor start relay (W10613606) — the click-buzz-click of a compressor that keeps trying and failing to start is the top no-cool cause on these Whirlpool-platform units. Dirty condenser coils, a dead evaporator fan (W10189703), or a stuck mechanical thermostat are next. Listen at the compressor first…

Most likely: on a front-loader, a torn or moldy door-boot seal — the top cause, and the tears hide in the bottom fold. A cracked tub-to-pump hose, oversudsing from non-HE detergent, or a leaking inlet valve are the others. Track where the water shows — front, bottom, or rear — to narrow it fast…

Bertazzoni Italian gas cooktop clicking but not lighting? European-design burner diagnostics, thermocouple safety, and spark module repair. Learn about...

Bertazzoni dishwasher not cleaning? Expert diagnosis of common causes, model-specific fixes, and repair costs for Bertazzoni dishwashers. Book same-day repair.

Amana compressor won't cycle off? Buried condenser coils and a tired gasket are the top causes on the Whirlpool platform. Ranked causes and DIY checks.

A leaking Bertazzoni dishwasher usually starts at the door gasket, a pump seal, or a spray-arm bearing. Here is the diagnosis, with the extra care a luxury Italian unit deserves.

Amana washer won’t spin? On the Whirlpool VMW platform it is usually the motor coupling, the lid switch, or the clutch. Ranked causes with fast checks for NTW and NFW models.

Bertazzoni induction zone not heating? Start with the magnet test for compatible cookware, then diagnose the power module (IGBT), zone sensor, or control board on Professional induction cooktops.
Let our professional technicians help. Same-day service available.