Want a regional phone & address? Pick your area.
Kenmore·Washerhigh severity
Kenmore Washer Error Code F7
Motor control error
Common Causes
- 1Motor control board failure
- 2Drive motor fault
- 3Wiring between motor and MCU
Step-by-Step Troubleshooting
- 1
Check motor wiring connector for burnt pins — high current causes connector damage
- 2
Measure motor winding resistance — should read 2-8 ohms per terminal pair
- 3
Inspect motor control board for scorched components or swollen capacitors
- 4
If motor tests good, replace the motor control unit (MCU)
Pro Diagnostic Tip
The 110-series direct-drive Kenmore pushes full motor phase current through a single MCU-to-motor plug, so one scorched pin there impersonates a dead motor. Ohm the three winding pairs right at the motor before buying a control unit — bolting a fresh MCU onto a shorted winding cooks the new board within seconds of the first spin ramp.
You Might Also Notice
- •Drum stays dead still through both wash and spin
- •Sharp electrical burn odor rising from under the tub
- •A strained hum from the motor with zero rotation
- •Cycle quits abruptly a moment into the spin ramp
Parts, Cost & Difficulty
Repair Difficulty
Professional OnlyEstimated Repair Cost
$200–$425
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
W10756692 motor control unit (MCU)W10677715 drive motor
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code F7 is a high-severity issue that can cause further damage to your washer if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Kenmore error code F7 mean?
Kenmore error code F7 indicates: Motor control error. This is a high-severity issue affecting your washer.
How do I fix Kenmore error code F7?
Check motor wiring connector for burnt pins — high current causes connector damage Then, Measure motor winding resistance — should read 2-8 ohms per terminal pair Then, Inspect motor control board for scorched components or swollen capacitors There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my washer has error F7?
Besides the error code on the display, common signs include: Drum stays dead still through both wash and spin; Sharp electrical burn odor rising from under the tub; A strained hum from the motor with zero rotation. If you notice any of these symptoms, check your washer's display panel for error code F7.
How much does it cost to fix Kenmore F7?
Repair costs for Kenmore F7 typically range from $200 to $425 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online