Want a regional phone & address? Pick your area.
Kenmore·Washerhigh severity
Kenmore Washer Error Code F25
Drive motor tachometer error
Common Causes
- 1Tachometer/hall sensor failure
- 2Motor wiring fault
- 3Drive motor failure
Step-by-Step Troubleshooting
- 1
Check tachometer coil on back of motor — measure resistance (typically 100-200 ohms)
- 2
Inspect motor connector for burnt or corroded pins
- 3
Spin drum by hand — resistance or grinding indicates bearing failure
- 4
If tachometer tests good, the MCU is not reading the signal — replace MCU
Pro Diagnostic Tip
On the Whirlpool-made 110-prefix Kenmore the tach is just a little pickup coil sitting behind the motor rotor that tells the board how fast the drum turns. It is a cheap, standalone part, so meter it and swap it on its own rather than buying the whole motor when the speed signal drops out.
You Might Also Notice
- •The motor kicks off then stalls a second later
- •The drum lurches and spins unevenly
- •Spin speed surges and sags through the cycle
Parts, Cost & Difficulty
Repair Difficulty
Professional OnlyEstimated Repair Cost
$200–$425
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
W10677715 drive motor with tachometerW10756692 motor control unit
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code F25 is a high-severity issue that can cause further damage to your washer if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Kenmore error code F25 mean?
Kenmore error code F25 indicates: Drive motor tachometer error. This is a high-severity issue affecting your washer.
How do I fix Kenmore error code F25?
Check tachometer coil on back of motor — measure resistance (typically 100-200 ohms) Then, Inspect motor connector for burnt or corroded pins Then, Spin drum by hand — resistance or grinding indicates bearing failure There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my washer has error F25?
Besides the error code on the display, common signs include: The motor kicks off then stalls a second later; The drum lurches and spins unevenly; Spin speed surges and sags through the cycle. If you notice any of these symptoms, check your washer's display panel for error code F25.
How much does it cost to fix Kenmore F25?
Repair costs for Kenmore F25 typically range from $200 to $425 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online