F1 E5 and two ovens in one
Maytag's list says F1 E5 may indicate a problem with the oven control or its associated wiring. On a double oven, whether a double wall oven or a range with two cavities, one control often manages both, so the code can stop one cavity while the other appears fine. That can tempt you to carry on using the working half. Restart once from the breaker and test both cavities. If F1 E5 returns, book a check before relying on either oven, because a control fault can affect both. A note of which cavity failed and when will help the technician.
Error codes
Reference| Code | Meaning |
|---|---|
| F1 E5 | There may be a problem with the Oven Control, or the associated wiring. |
F1 E5 on a double oven
- One cavity will not heat — The other may still work normally. Note which one is affected.
- The code with both cavities in use — Running both at once puts the most load on the control.
- Settings landing on the wrong cavity — The display may seem confused between upper and lower. Note exactly what you pressed and what happened.
- The code clearing after a restart — It may come back when both ovens heat together.
- Uneven results in the working cavity — Worth noting, as it may be part of the same fault.
Ranked causes of F1 E5
- The oven control — First: on a double oven it carries the load of both cavities, which adds heat and wear.
- A connector on one cavity's circuit — Second: a loose plug on the harness to one oven can stop that cavity alone.
- Wiring between the cavities — Third: harnesses run close to both heat sources. Heat from the lower oven rises past the upper harness.
- A supply problem — Fourth: two ovens heating at once draw heavily on the connection where power enters.
Checks for both cavities
- Restart once — Switch the breaker off for a few minutes, then on.
- Test the upper cavity alone — A short bake while the lower one stays off.
- Test the lower cavity alone — Then the other way round.
- Test both together — Only if each worked alone; watch for the code. Give each cavity a few minutes to come up to heat.
- Note the pattern — Which cavity, which function, and when F1 E5 appeared.
Owner steps for F1 E5
- Power-cycle at the panel — Restore power after a pause.
About 5 min
- Run each cavity separately — Check that each heats, using an oven thermometer.
Tools: oven thermometerAbout 30 min
- Run both together briefly — Watch the display for the code.
About 15 min
- Record the results — Which cavity failed and when.
Tools: notepadAbout 3 min
- Book a check if F1 E5 returns — The control and the harness are tested with the power off.
Tools: ::
Safety with a double oven fault
Safety
Do not assume the working cavity is unaffected; a control fault can change how either oven switches on and off. Never leave either oven heating unattended while the code is unresolved. If either cavity heats when nothing is set, or anything smells of burning, switch the whole unit off at the breaker. Keep panels in place, as the wiring behind them carries mains power.
When F1 E5 needs a professional
Call if F1 E5 returns after a restart, if one cavity stays dead, or if the code appears whenever both ovens run together. Tell the technician which cavity failed and under what conditions, as that narrows the search between the control and each harness. If the unit is built into cabinetry, mention it, because access to the back of a wall oven takes extra time.
Maytag double-oven and control codes
Ovens this covers
This page covers Maytag double wall ovens and double-cavity ranges that list F1 E5, and applies equally to single ovens with the same code. It does not cover microwaves, cooktops or other brands. No model-specific F1 E5 page exists yet.
Maytag oven code list, complete
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
