The short answer
A Costway FP Washer that stops part way, repeats a step endlessly or finishes with a wet load is describing a permission problem rather than a mechanical failure. Every stall has a condition behind it, and identifying which condition is missing is the whole job.
What you see on the FP family
- The cycle stops with the tub part full and nothing happening — A fill that never reached the level the machine expects, which points at the taps, the screens or the pressure sensing.
- It repeats the same step over and over — Usually the machine re-attempting a balance or a drain it cannot complete, rather than a control fault.
- It finishes but the load is soaking wet — The spin never ran, most often because water was still in the tub when the machine wanted to spin.
- The cycle time jumps up part way through — Normal on machines that extend a step to re-balance or re-drain. It only matters when the step never completes.
Causes, most likely first on the FP family
- Fill problems — taps, inlet screens or pressure sensing — Ranked first on the FP family — A stall early in the cycle on the Costway FP washer family is a fill problem far more often than anything electronic, and both taps are free to check. A machine that cannot fill to its expected level waits rather than fails. Closed taps, silted inlet screens and a blocked pressure hose all produce a cycle that stalls politely at the beginning.
- Drain not completing within the time allowed — Second — and it connects this page to the drainage page for this family. Most machines will not spin until the tub is empty, and they will retry the drain before giving up. A partly blocked filter or hose produces a cycle that repeats and then stops with a wet load.
- Lid or door lock not staying confirmed — Third — it is the same wear that causes start refusals, seen later in the cycle. The lock has to stay made for the whole cycle. A marginal switch that opens under vibration pauses the machine mid-step, and the cycle then resumes or stalls depending on the design.
- Unbalanced loads, or the control board — Fourth — the board is the part owners suspect first and the part that fails least on these models. A load the machine cannot balance triggers repeated redistribution attempts and eventually an abandoned spin. A genuinely failed board is rare and usually follows a water intrusion or a supply event.
- Body: The order below follows the shared parts rather than the differences — the stems in the FP family carry the same running gear and diverge at the cabinet — which is why the top of this list is not where the brand-generic article puts it.
Check in this order, and why
- 1. Note exactly where in the cycle it stops — Fill, wash, drain or spin. That one observation points at a different sensor for each answer and costs nothing.
- 2. Look in the tub when it stalls — Water still present at the spin step means the fault is drainage rather than the cycle itself.
- 3. Check both taps are fully open and the inlet screens are clear — An early stall is usually a fill the machine never completed, and the screens silt up invisibly.
- Body: The stems in the FP family share their layout, so the order below holds across the table; where a stem differs it differs at the cabinet, not at the part you are reaching for.
Before you open anything
Safety
Unplug the appliance or switch off its breaker before removing any panel — a capacitor can hold a charge after the power is off. Do not force a locked door: most designs release the lock only after the tub has drained and come to rest, and forcing it breaks the latch rather than opening it. Shut both taps before touching any inlet fitting.
Models in the FP family
Reference| Model number | Family key |
|---|---|
| FP11187US-GR | costway:washer:fp |
| FP11187US-WH | costway:washer:fp |
| FP11188US-GR | costway:washer:fp |
| FP11188US-WH | costway:washer:fp |
| FP11212US-GR | costway:washer:fp |
| FP11212US-WH | costway:washer:fp |
| FP11213US-GR | costway:washer:fp |
| FP11213US-WH | costway:washer:fp |
| FP11214US-GR | costway:washer:fp |
| FP11214US-WH | costway:washer:fp |
| FP11215US-GR | costway:washer:fp |
| FP11215US-WH | costway:washer:fp |
| FP11216US-GR | costway:washer:fp |
| FP11216US-WH | costway:washer:fp |
| FP11217US-GR | costway:washer:fp |
| FP11217US-WH | costway:washer:fp |
| FP11218US-GR | costway:washer:fp |
| FP11219US-GR | costway:washer:fp |
| FP11219US-WH | costway:washer:fp |
| FP11220US-GR | costway:washer:fp |
| FP11220US-WH | costway:washer:fp |
| FP11221US-GR | costway:washer:fp |
| FP11221US-WH | costway:washer:fp |
| FP11222US-GR | costway:washer:fp |
| FP11222US-WH | costway:washer:fp |
| FP11223US-GR | costway:washer:fp |
| FP11223US-WH | costway:washer:fp |
When to call a technician
On the Costway FP washer family the owner line is the taps, the screens, the filter and the load. Those four settle most cycle complaints without a visit. The pressure switch, the lock assembly and the board are service parts, and a machine stalling with a locked door and a wet load should not be forced open.
Other FP washer pages
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
