The short answer
A Maytag oven showing 9d41 has flagged the door latch and switch. The exact documented wording is in the table; the order of the checks below it is the part worth reading twice. Leave the function that needs the door locked alone until the latch works.
The documented code and its meaning
Reference| Code | Meaning |
|---|---|
| 9d41 | There may be a problem with the Oven Door Latch Assembly, the Door Switch, or the associated wiring. |
What you actually observe
- The latch releases eventually but takes far longer than it used to — A mechanism slowing down is one that will shortly stop.
- The code followed a heavy spill or a cleaning cycle — Hardened residue around the strike is a routine finding afterwards.
- The door will not lock when the cycle asks it to — You can usually hear the attempt and hear it stop short.
- NEAR MISS — the door closes and locks normally and the code still shows — Then the switch is reporting incorrectly and the mechanism is fine.
Causes, most likely first on this oven
- A latch motor or cam not completing its travel — The switch only closes at the very end of the stroke, so a latch that is nearly there reports as a latch that never arrived.
- A door switch that no longer changes state — Latch switches weld closed about as often as they fail open, so the control can be told the door is shut when it is not — or open when it is not.
- The door and the frame out of alignment — A door that has dropped on its hinges, or a strike that has shifted, stops the latch reaching its seat with nothing electrical wrong anywhere.
- The wiring between the latch assembly and the control — The loom crosses the hinge on many designs, and the hinge is the only part of the appliance that bends every day.
Check in this order, and why
- Work the door slowly and listen to the latch — Hesitation, a buzz, or a stroke that stops short answers this before any tool is picked up.
- Check that the door sits square against the frame all the way round — An even gap rules out the mechanical half of this fault for free.
- Look for anything trapped in the latch path — Foil, a rack, packaging or a dropped screw in the latch path is a routine finding.
- Leave the latch assembly itself until the alignment is confirmed — Put a latch on a door that is out of line and the code is back the same afternoon.
What an owner can safely check
- Take the power off, then work the door by hand and watch the latch — You are looking for a latch that reaches its seat smoothly, not for anything electrical.
Tools: flashlightAbout 8 min
- Clear anything trapped around the latch or the strike plate — Hardened spill on the strike plate takes away just enough travel to cause this.
Tools: soft clothAbout 10 min
- Power the unit back up and try one short cycle with the door closed firmly — If a deliberate firm close clears it, the fault is alignment and not electronics.
About 5 min
Before anything is opened
Safety
Take the power away first: unplug the appliance or switch off its breaker before removing any panel, since a capacitor can hold a charge after the power is off. Built-in ovens rarely have a plug; the breaker is what isolates them. Cavity and door glass hold heat long after the cycle has finished. Do not re-route or hold closed anything on the door circuit; it takes power away at a point the design depends on.
When this stops being an owner job
Book the visit if the latch does not complete its travel, or the code stays after the door path is clear. At that point the next step is a meter or a panel off, and the oven generally has to come out of its housing before the connections behind it can be seen. Do not wait at all if there is a burning smell, visible scorching, or a breaker that trips the moment the appliance starts. Those three override everything above.
Nearest error-code pages
What this page does not cover
This is the platform-level reading of 9d41: it holds for the Maytag oven families that share that control generation. It stops short of older platforms that display the same characters for a different condition, and it carries no family-specific detail at all — no wiring colours, no pin numbers, no torque figures, no part numbers. Those belong on the page for the family concerned. Where such a page exists it outranks this one, and the code index below is where it is listed.
Other Maytag oven codes
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
