The short answer
4d41 is how this oven reports a problem in the cooling fan circuit. The code table records the documented meaning, and the causes below it are ordered by how often each one is the answer. Keep the runs short until the cooling path has been checked.
The documented code and its meaning
Reference| Code | Meaning |
|---|---|
| 4d41 | Cooling fan speed too high. |
What you actually observe
- The fan cannot be heard at the end of a cycle — It should run on after the heat stops; silence is the key observation.
- The fan runs louder or rougher than it used to — Bearings announce themselves before they seize.
- The cabinetry or the wall above the oven feels unusually warm — Heat that is not being carried away shows up outside the appliance.
- NEAR MISS — the fan runs constantly and never stops — A fan that will not stop is the opposite fault and a different page.
Causes, most likely first on this oven
- A restricted air path around the appliance — Blocked intake or exhaust slows the fan against back pressure, and the control reads the speed, not the blockage.
- A fan motor with worn bearings or a fouled blade — Dust and grease load the blade, so the motor slows under its own contamination well before it stops.
- The wiring or plug feeding the fan — A high-resistance joint drops the voltage at the motor, which shows up as a speed fault rather than a dead fan.
- The control output that drives and monitors the fan — Last: the control reports far more fan faults than it ever causes.
Check in this order, and why
- Listen for the fan at the end of a cycle — It should run on after the heat stops; silence there is the most useful single observation.
- Check the vents and surrounding cabinetry for obstruction — Trim, packaging and stored items across an intake are routine findings.
- Feel whether the exhaust air is warm and moving — Warm still air means the heat is there and the fan is not moving it.
- Leave motor and wiring to a technician — The motor sits behind the fascia and is not reachable without dismantling the control area.
What an owner can safely check
- Clear anything stacked against the vents or the trim — Restriction outside the appliance is the one cause an owner can remove outright.
About 10 min
- Run a short cycle and listen for the fan running on afterwards — This is the cheapest confirmation that the motor is turning at all.
About 15 min
- Drop the breaker for a minute if the fan never starts — A stuck output sometimes releases; a code that returns is a real fault.
About 3 min
Before anything is opened
Safety
Power off before panels off. Unplug the appliance or switch off its breaker before removing any panel; a capacitor can hold a charge after the power is off. A built-in oven is normally hard-wired, so the breaker is the isolation point rather than a plug. The cavity and the door glass stay hot for a long time after a bake cycle ends. Leave the interlocking switches wired as they came. They exist to remove power at the moment it has to go.
When this stops being an owner job
Arrange a visit if the fan is silent, or the code returns with the vents clear. Past there the work needs a meter or a panel removed, and a wall oven has to be unseated from its cabinet before the rear connections are reachable. Three things override that timing: a burning smell, scorch marks near the controls, and a breaker that trips on start-up. Any of them means stop and call now.
Nearest error-code pages
What this page does not cover
Treat this as the family-agnostic reading of 4d41 for Maytag oven models on the common control platform. It does not extend to earlier control generations that happen to display the same characters for a different condition. Wiring colours, pin assignments, torque values and part numbers are all left out on purpose: they are family-specific and belong on the page for that family. Where such a page exists, it is the more specific answer and takes precedence over this one; the linked index is where to find it.
Other Maytag oven codes
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
