The short answer
This page covers the dual-zone models, where one cabinet runs two compartments at different temperatures. On a dual-zone unit each compartment reports separately, so a code names a zone as well as a condition. A refrigerator holds food safely at 40 °F (4 °C) or below.
What you are seeing
- One compartment behaves differently from the other
- A code on the display with the compressor stopped
- A code that appears only when the engine is off
- A code that appears on hot days and clears in the evening
- The display working while the compressor never runs
- The unit forgetting its setting each time it is reconnected
- Body: The code and what accompanies it are the diagnosis: One compartment behaves differently from the other. A code on the display with the compressor stopped. A code that appears only when the engine is off. A code that appears on hot days and clears in the evening. The display working while the compressor never runs. The unit forgetting its setting each time it is reconnected.
Causes, most likely first
- A code naming one compartment only — Why: a dual-zone unit reports per compartment, so a code on one side says nothing about the other and each must be verified with its own thermometer.
- Two setpoints too far apart for the design — Why: asking for a large difference between compartments raises a condition on the compartment that loses, and no reset will clear it.
- Supply voltage below the protection threshold — Why: the most common code on this class of appliance exists to protect a vehicle battery, and it appears whenever the supply sags under compressor load.
- A high-ambient or overheat condition — Why: the unit stops the compressor when it cannot reject heat, so a code that appears on hot afternoons and clears in the evening is reporting the environment rather than a fault.
- A blocked vent or fan raising the same condition — Why: the same protection triggers when the vents are packed against luggage, and clearing them clears the code.
- A sensor the unit cannot read — Why: this gives a code with the fan and display working normally, and it is the first cause in the list that is genuinely internal.
- Body: Ranked by what these codes actually report: First, A code naming one compartment only: a dual-zone unit reports per compartment, so a code on one side says nothing about the other and each must be verified with its own thermometer. Second, Two setpoints too far apart for the design: asking for a large difference between compartments raises a condition on the compartment that loses, and no reset will clear it. Third, Supply voltage below the protection threshold: the most common code on this class of appliance exists to protect a vehicle battery, and it appears whenever the supply sags under compressor load. Fourth, A high-ambient or overheat condition: the unit stops the compressor when it cannot reject heat, so a code that appears on hot afternoons and clears in the evening is reporting the environment rather than a fault. Fifth, A blocked vent or fan raising the same condition: the same protection triggers when the vents are packed against luggage, and clearing them clears the code. Sixth, A sensor the unit cannot read: this gives a code with the fan and display working normally, and it is the first cause in the list that is genuinely internal.
What to check, in order
- verify each compartment separately with its own thermometer, because a dual-zone code is always about one side.
- note the exact code and what the unit was connected to when it appeared, because supply codes and ambient codes look identical without that context.
- look it up in the manual for your model rather than for the brand, since these units are sold under several names with different tables.
- try the unit on mains power: a code that disappears on mains is a low-voltage supply code.
- Body: Follow the code to the supply and the environment first: First, verify each compartment separately with its own thermometer, because a dual-zone code is always about one side. Second, note the exact code and what the unit was connected to when it appeared, because supply codes and ambient codes look identical without that context. Third, look it up in the manual for your model rather than for the brand, since these units are sold under several names with different tables. Fourth, try the unit on mains power: a code that disappears on mains is a low-voltage supply code.
Checks you can do yourself
- Put a thermometer in each compartment and read both after a full day — Tools: two thermometers — Time estimate: a few minutes
- Photograph the code and note what the unit was connected to and how hot it was — Tools: phone — Time estimate: a few minutes
- Find the code in the manual for your model and read what condition it reports — Tools: the model manual — Time estimate: a few minutes
- Connect the unit to mains power and see whether the code clears and the compressor runs — Tools: the mains adapter — Time estimate: a few minutes
- Set the battery-protection mode to its lowest setting and retry on the low-voltage supply — Tools: the model manual — Time estimate: a few minutes
- Body: Owner checks stop at the supply and the vents: Put a thermometer in each compartment and read both after a full day (two thermometers; a few minutes). Photograph the code and note what the unit was connected to and how hot it was (phone; a few minutes). Find the code in the manual for your model and read what condition it reports (the model manual; a few minutes). Connect the unit to mains power and see whether the code clears and the compressor runs (the mains adapter; a few minutes). Set the battery-protection mode to its lowest setting and retry on the low-voltage supply (the model manual; a few minutes).
Safety first
Safety
A refrigerator holds food safely at 40 °F (4 °C) or below. Unplug the appliance or switch off its breaker before removing any panel. A capacitor can hold a charge after the power is off. Do not defeat a protection setting to keep the compressor running from a vehicle battery: that protection exists so the vehicle will still start. Stop using any lead or socket that becomes warm. unplug-before-service fridge-40f
When to stop and call a technician
These need a technician: One compartment fails with both switched on, both set alike and both seals proven. The code persists on mains power with clear vents and a normal ambient. The display works and the compressor never runs on any supply. The code names a sensor or a component rather than a supply condition. One compartment fails with both switched on, both set alike and both seals proven The code persists on mains power with clear vents and a normal ambient The display works and the compressor never runs on any supply The code names a sensor or a component rather than a supply condition
Nearest pages of the same kind
What this page does not cover
This page is generalized across every cooler sold under the BODEGA name: it separates neither the dual-zone models from the single-zone ones and the portable boxes from the indoor cabinets, and it names no individual model. Where a family- or model-specific page exists it is linked here and it outranks this one for that machine; at present no page beneath this one narrows to a single family, so treat the ranking above as the brand-level pattern rather than a reading of your serial plate. This page covers the dual-zone models specifically; companion pages cover the portable form, the indoor beverage-cooler form and the deeper diagnostic tier. For the other faults that turn up on this machine, start from Common BODEGAï¼BODEGACOOLER Refrigerator Problems.
Links down: - [The same units — portable low-voltage form](/blog/bodega-bodegacooler-aobosi-aaobosi-refrigerator-problems) - [The same units — after the basic checks](/blog/bodega-cooler-refrigerator-problems)
Related pages
- Common BODEGAï¼BODEGACOOLER Refrigerator Problems
- BODEGAï¼BODEGACOOLER Refrigerator: Abnormal Noise or Vibration
- BODEGAï¼BODEGACOOLER Refrigerator: Not Cooling or Not Freezing
- BODEGAï¼BODEGACOOLER Refrigerator: Door, Latch or Seal Fault
- BODEGAï¼BODEGACOOLER Refrigerator: Ice Maker Fault
- BODEGAï¼BODEGACOOLER Refrigerator: Water Leak
- BODEGAï¼BODEGACOOLER Refrigerator: Will Not Start or No Power
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
