Want a regional phone & address? Pick your area.
Whirlpool·Washermedium severity
Whirlpool Error Code F9E1
Long drain
Common Causes
- 1Clogged filter
- 2Kinked drain hose
Step-by-Step Troubleshooting
- 1
Locate and clean the drain pump filter — on front-loaders, it is behind the small access panel at the bottom front
- 2
Place towels and a shallow pan under the filter before opening, as trapped water will flow out
- 3
Inspect the drain hose for kinks, especially where it connects to the standpipe or utility sink
- 4
Check that the drain hose end is not pushed more than 8 inches into the standpipe (creates siphon)
- 5
If filter and hose are clear, the drain pump impeller may be broken — listen for humming without water flow
Pro Diagnostic Tip
On Whirlpool and Maytag front-loaders, coins, hair pins, and bra underwires are the top items found in the drain pump filter. The pump filter should be cleaned quarterly. If the pump hums loudly but water does not flow, the impeller blades are likely broken — the pump must be replaced.
You Might Also Notice
- •Water remains in the drum after cycle completes
- •Drain pump runs for extended periods
- •Clothes come out soaking wet
- •Foul odor from standing water in the tub
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$0–$250
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
WPW10730972 Drain Pump MotorW10906534 Drain Hose Extension Kit
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Clean drain pump filter and check hose
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F9E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
$89 → $0 Service Call & Diagnosis — offer ends May 31
Frequently Asked Questions
What does Whirlpool error code F9E1 mean?
Whirlpool error code F9E1 indicates: Long drain. This is a medium-severity issue affecting your washer.
How do I fix Whirlpool error code F9E1?
Locate and clean the drain pump filter — on front-loaders, it is behind the small access panel at the bottom front Then, Place towels and a shallow pan under the filter before opening, as trapped water will flow out Then, Inspect the drain hose for kinks, especially where it connects to the standpipe or utility sink There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error F9E1?
Besides the error code on the display, common signs include: Water remains in the drum after cycle completes; Drain pump runs for extended periods; Clothes come out soaking wet. If you notice any of these symptoms, check your washer's display panel for error code F9E1.
How much does it cost to fix Whirlpool F9E1?
Repair costs for Whirlpool F9E1 typically range from $0 to $250 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.