Want a regional phone & address? Pick your area.
Whirlpool Appliance Error Codes
Complete reference guide with 50+ error codes for Whirlpool appliances, including Maytag, KitchenAid, Amana, Jenn-Air. Find your error code below, understand the cause, and learn if it's a DIY fix or needs professional repair.
Parent company: Whirlpool Corporation | Also covers: Maytag, KitchenAid, Amana, Jenn-Air
Real Whirlpool Repair Photos
Got an error code? Don't decode it alone.
Book a free diagnostic — our technician reads the code, finds the real cause, and quotes the fix on-site.
or call (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
| Code | Description | Severity |
|---|---|---|
| F0E1 Also: rL | Load in tub during clean cycle Causes: Laundry left in the drum when Clean Washer was started, Small item wedged under the impeller plate skewing the weight read, Load-sense baseline drifted so an empty tub still reads weight | low |
| F0E2 | Overload detected Causes: Drum packed past its rated dry-weight capacity, A single dense item (rug, comforter) exceeding the safe extraction mass, Motor-current weight estimate reading high from a worn rotor-position sensor | low |
| F0E5 | Load imbalance Causes: Clothes clumped to one side so the basket cannot balance for spin, Machine not sitting level on the laundry-room floor, Worn suspension rods or springs letting the tub swing off-axis, Mixed heavy and light items settling unevenly during the ramp to spin | low |
| F1E1 | Motor control error Causes: Motor control unit failed after a line-voltage surge, Triac on the drive board shorted, stalling the motor mid-cycle, Poor ground or loose neutral feeding erratic voltage to the board, Heat-cracked solder joints on the power stage from years of duty cycling | high |
| F1E2 | Motor error Causes: Motor failure, Wiring issue | high |
| F2E1 | Stuck key / user interface Causes: A console pad reading as held down longer than the stuck-key timeout, Detergent film under the touch panel bridging a pad contact, Trapped moisture warping the membrane against the board behind it | medium |
| F3E1 | Pressure switch / water level Causes: Analog water-level transducer out of calibration, Silted sensing chamber beneath the outer tub, Cracked or perished sensing tube to the transducer port, Corroded control-board connector at the level-sensor input | high |
| F5E1 | Door switch error Causes: Door-closed sense switch failed open, Worn strike hook no longer depressing the switch plunger, Broken conductor in the door-switch harness at the flex point | medium |
| F5E2 | Door lock error Causes: Wax-motor actuator in the door lock worn out, Lock plunger jammed by lint or a warped latch lever, Lock-feedback switch not confirming the bolt is thrown, Overheated lock coil after repeated rapid start attempts | medium |
| F5E3 | Lid lock error Causes: Motorized lid-lock cam stripped so the bolt never seats, Lock-state microswitch stuck, so the board cannot confirm a locked lid, Striker tab bent or missing where the lid meets the console bridge, Auto-relock timing out because the lid rebounds open on a tired hinge spring | medium |
| F7E1 | Motor speed sensor Causes: Speed-feedback pickup no longer reporting basket RPM to the board, Fractured magnet ring on the rotor giving a gapped tach pulse, Debris in the stator-to-rotor gap dragging the basket below commanded speed, Loose rotor bolt letting the position ring wobble past the pickup | high |
| F8E1 Also: LF | Long fill / water supply Causes: Target water volume not reached inside the fill-timeout window, Scale-choked inlet screens throttling the incoming flow, House supply pressure too low to satisfy the flow the board expects, One inlet solenoid open-circuit so only half the water arrives | medium |
| F8E3 | Overflow Causes: Inlet valve stuck, Pressure switch failure | high |
| F9E1 Also: Ld | Long drain Causes: Coin-trap filter packed with lint, debris, and small objects, Drain pump impeller sheared so it spins without moving water, Standpipe set too high or the hose shoved in deep enough to siphon, Sock or wire drawn into the pump volute, stalling the impeller | medium |
| Sud Also: Sd | Excessive suds Causes: Non-HE detergent foaming far past what the drum can clear, Too large a detergent dose for the sensed load size, Slow drain leaving foam behind so suds accumulate load over load | low |
| HC | Hot/cold hoses reversed Causes: Supply hoses crossed at the washer inlets during installation, Hot and cold swapped at the wall valves rather than the machine, One inlet thermistor drifted, making correct hoses read as reversed | low |
| F6E1 | Central control communication error Causes: Serial harness unseated between the central control and the motor control, Corroded connector pins after moisture intrusion, Failed central control unit, Failed motor control unit | high |
| F8E2 | Dispenser system fault Causes: Dispenser motor or actuator failed, Diverter jammed with hardened detergent or softener, Harness fault to the dispenser motor, Control board dispenser-output failure | medium |
| uL | Unbalanced load during spin Causes: A single heavy item thrown to one side of the basket, A small load unable to distribute evenly, The washer not sitting level on the floor, Worn suspension rods or shocks no longer damping the basket | low |
| F3E2 | Water temperature sensor fault Causes: Open or shorted inlet water thermistor, Harness fault to the temperature sensor, Connector corrosion at the sensor, Control board sensor-input failure | medium |
When to Call a Professional
- Error code returns after power reset
- Code is marked as high severity
- Appliance is leaking water, making unusual noises, or smells like burning
- You're not comfortable working with electrical or gas appliances
Whirlpool Error Codes — FAQ
What are the most common Whirlpool error codes?
The most common Whirlpool error codes relate to temperature sensors, drainage issues, motor errors, and communication failures. Check our complete list above for your specific code, or call EasyBear for professional diagnosis.
How do I reset my Whirlpool appliance after an error code?
For most Whirlpool appliances, unplug the unit or turn off the circuit breaker for 60 seconds, then restore power. If the error code returns after reset, the underlying issue needs professional repair.
Can I fix a Whirlpool error code myself?
Some Whirlpool error codes indicate simple issues like unbalanced loads, clogged filters, or suds buildup that you can fix yourself. Our table above marks each code as DIY-fixable or requiring professional service. For high-severity codes, always call a professional technician.
How much does Whirlpool appliance repair cost?
Whirlpool appliance repair cost depends on the specific issue, model, and parts needed. At EasyBear, diagnosis is always free when you proceed with the repair. Your technician provides a transparent quote after identifying the problem, so you know the exact cost before any work begins.
Does Whirlpool warranty cover error code repairs?
Whirlpool manufacturer warranty typically covers defects for 1-2 years from purchase. Some components (like LG linear compressors) have extended coverage. Our technicians can verify your warranty status and handle claims. Even out-of-warranty repairs are affordable with EasyBear.
Do Maytag and KitchenAid and Amana and Jenn-Air use the same error codes as Whirlpool?
Maytag, KitchenAid, Amana, Jenn-Air are part of the Whirlpool family and often share similar platforms and error code systems. However, some models may have unique codes. Our reference covers error codes for all brands in this family.
Call NowAvailable 24/7 — call or textBook Online