Want a regional phone & address? Pick your area.
Midea·Dishwasherlow severity
Midea Dishwasher Error Code E5
Overtemperature / temperature sensor out of range
Common Causes
- 1NTC sensor shorted
- 2Heater relay stuck closed
- 3Sensor wiring pinched
- 4Connector corroded in the sump
Step-by-Step Troubleshooting
- 1
Unplug the dishwasher and access the sump and heater area from the base
- 2
Locate the NTC temperature sensor near the flow-through heater
- 3
Measure the sensor resistance cold — a near-zero reading indicates a shorted sensor
- 4
Inspect the wiring for pinch damage and the connector for sump-moisture corrosion
- 5
Replace the NTC sensor, and if the water was genuinely too hot, check the heater relay for sticking
Pro Diagnostic Tip
If E5 pairs with visibly steaming, overly-hot water, suspect a stuck heater relay on the board rather than the sensor — the sensor is reading a real overtemperature.
You Might Also Notice
- •Cycle aborts partway through
- •Water hotter than normal
- •Error clears then returns on the next hot cycle
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$80–$180
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
NTC temperature sensor
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E5 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Midea error code E5 mean?
Midea error code E5 indicates: Overtemperature / temperature sensor out of range. This is a low-severity issue affecting your dishwasher.
How do I fix Midea error code E5?
Unplug the dishwasher and access the sump and heater area from the base Then, Locate the NTC temperature sensor near the flow-through heater Then, Measure the sensor resistance cold — a near-zero reading indicates a shorted sensor There are 2 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my dishwasher has error E5?
Besides the error code on the display, common signs include: Cycle aborts partway through; Water hotter than normal; Error clears then returns on the next hot cycle. If you notice any of these symptoms, check your dishwasher's display panel for error code E5.
How much does it cost to fix Midea E5?
Repair costs for Midea E5 typically range from $80 to $180 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online