Want a regional phone & address? Pick your area.
Midea·Dishwasherlow severity
Midea Dishwasher Error Code E8
Distribution valve / spray-arm switching fault
Common Causes
- 1Diverter motor failed
- 2Diverter position switch fault
- 3Debris jamming the diverter
- 4Wiring open to the diverter
Step-by-Step Troubleshooting
- 1
Unplug the dishwasher and reach the wash-pump diverter housing from the base
- 2
During a cycle, listen for the diverter to switch flow between the upper and lower arms
- 3
Remove and inspect the diverter flap for food debris or a worn seat
- 4
Test the diverter motor and its position switch for continuity
- 5
Replace the diverter assembly if the motor is dead or the flap will not seat
Pro Diagnostic Tip
E8 typically shows as one rack cleaning well while the other stays dirty. Note which arm is starved — it identifies the diverter position that has failed.
You Might Also Notice
- •Only the top or bottom rack gets clean
- •Uneven wash results
- •Repeated clunk from under the tub
Parts, Cost & Difficulty
Repair Difficulty
Hard — Advanced Skills RequiredEstimated Repair Cost
$110–$250
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Diverter valve assembly
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E8 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Midea error code E8 mean?
Midea error code E8 indicates: Distribution valve / spray-arm switching fault. This is a low-severity issue affecting your dishwasher.
How do I fix Midea error code E8?
Unplug the dishwasher and reach the wash-pump diverter housing from the base Then, During a cycle, listen for the diverter to switch flow between the upper and lower arms Then, Remove and inspect the diverter flap for food debris or a worn seat There are 2 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my dishwasher has error E8?
Besides the error code on the display, common signs include: Only the top or bottom rack gets clean; Uneven wash results; Repeated clunk from under the tub. If you notice any of these symptoms, check your dishwasher's display panel for error code E8.
How much does it cost to fix Midea E8?
Repair costs for Midea E8 typically range from $110 to $250 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online