Want a regional phone & address? Pick your area.
Midea·Dishwashermedium severity
Midea Dishwasher Error Code E3
Water not heated to required temperature
Common Causes
- 1Flow-through heater failed
- 2Thermal fuse tripped
- 3NTC feedback out of range
- 4Board heater relay fault
Step-by-Step Troubleshooting
- 1
Unplug the dishwasher and pull it out to reach the sump and pump housing
- 2
Find the flow-through heater built into the wash-pump body and inspect its terminals
- 3
Measure the heater resistance — an open circuit confirms a failed heating element
- 4
Check any inline thermal fuse for continuity; a tripped fuse blocks heating
- 5
Replace the heater/pump assembly if the element reads open or a terminal is scorched
Pro Diagnostic Tip
Midea integrates the heater into the circulation pump rather than a tub-floor element. E3 with good wash action but cold water almost always means the heater section of that pump has opened.
You Might Also Notice
- •Cold water throughout the cycle
- •Wet, poorly dried dishes
- •Greasy film left on glassware
Parts, Cost & Difficulty
Repair Difficulty
Hard — Advanced Skills RequiredEstimated Repair Cost
$120–$290
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Flow-through heater / wash-pump assemblyThermal fuse
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E3 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Midea error code E3 mean?
Midea error code E3 indicates: Water not heated to required temperature. This is a medium-severity issue affecting your dishwasher.
How do I fix Midea error code E3?
Unplug the dishwasher and pull it out to reach the sump and pump housing Then, Find the flow-through heater built into the wash-pump body and inspect its terminals Then, Measure the heater resistance — an open circuit confirms a failed heating element There are 2 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my dishwasher has error E3?
Besides the error code on the display, common signs include: Cold water throughout the cycle; Wet, poorly dried dishes; Greasy film left on glassware. If you notice any of these symptoms, check your dishwasher's display panel for error code E3.
How much does it cost to fix Midea E3?
Repair costs for Midea E3 typically range from $120 to $290 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online