Want a regional phone & address? Pick your area.
Fisher & Paykel·Dishwashermedium severity
Fisher & Paykel Dishwasher Error Code F3
Water fill fault
Common Causes
- 1Water supply valve closed or only partly open
- 2Failed inlet valve solenoid
- 3Clogged inlet filter screen
- 4Low household water pressure or a kinked inlet hose
Step-by-Step Troubleshooting
- 1
Verify the supply stopcock under the sink is fully open and the inlet hose runs without kinks
- 2
Disconnect the inlet hose and clean the mesh filter screen where it meets the valve
- 3
Confirm household water pressure is adequate — a DishDrawer needs a steady supply to fill in time
- 4
Test the inlet valve solenoid for continuity; an open solenoid will not admit water
- 5
Restore power and watch a fill — no water with good supply confirms the inlet valve
Pro Diagnostic Tip
The fill timeout is typically 90-120 seconds. When supply and pressure are good but the drawer still will not fill, the inlet valve solenoid has usually failed — test it for continuity before replacing anything else.
You Might Also Notice
- •Cycle stalls at the start
- •No water entering the drawer
- •Unusually long fill
- •Drawer indicator flashing at the beginning of a cycle
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$150–$350
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Water inlet valveInlet filter screenInlet hose
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Confirm the water supply stopcock is fully open and the inlet hose is not kinked
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F3 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Fisher & Paykel error code F3 mean?
Fisher & Paykel error code F3 indicates: Water fill fault. This is a medium-severity issue affecting your dishwasher.
How do I fix Fisher & Paykel error code F3?
Verify the supply stopcock under the sink is fully open and the inlet hose runs without kinks Then, Disconnect the inlet hose and clean the mesh filter screen where it meets the valve Then, Confirm household water pressure is adequate — a DishDrawer needs a steady supply to fill in time There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error F3?
Besides the error code on the display, common signs include: Cycle stalls at the start; No water entering the drawer; Unusually long fill. If you notice any of these symptoms, check your dishwasher's display panel for error code F3.
How much does it cost to fix Fisher & Paykel F3?
Repair costs for Fisher & Paykel F3 typically range from $150 to $350 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online