Want a regional phone & address? Pick your area.
Fisher & Paykel·Dishwasherhigh severity
Fisher & Paykel Dishwasher Error Code F1
Water leak detected in the base
Common Causes
- 1Water spilled or overfilled into the base pan
- 2Leaking wash pump seal or a loose hose fitting
- 3Cracked tub or sump letting water into the base
- 4Stuck or failed flood-switch float
A repeating F1 means water is entering the base for a reason — keep looking for the leak source rather than resetting repeatedly, or the leak will worsen.
Step-by-Step Troubleshooting
- 1
Tilt the DishDrawer backward so the base pan drains, then dry the pan completely with a towel
- 2
Reset power at the wall and start a short cycle to see whether the fault returns
- 3
If it returns, inspect the drain and fill hose fittings and the wash pump seal for a slow leak
- 4
Check that the flood-switch float in the base moves freely and is not held up by debris
- 5
On double-drawer models, run each drawer separately to isolate which one is leaking
Pro Diagnostic Tip
F1 is the most common DishDrawer fault. On double-drawer units the base-pan flood switch is shared, so F1 disables BOTH drawers even when only one leaked — always drain and dry the base pan before resetting, and treat a recurring F1 as a real leak, not a false trip.
You Might Also Notice
- •Both drawers dead or refusing to start
- •Water pooled under the cabinet
- •Drain pump running continuously
- •Cycle stops immediately after starting
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$150–$400
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Flood switchWash pump sealDrain or fill hoseBase pan assembly
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Tilt the unit backward to drain the base pan, dry it, then reset
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code F1 is a high-severity issue that can cause further damage to your dishwasher if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Fisher & Paykel error code F1 mean?
Fisher & Paykel error code F1 indicates: Water leak detected in the base. This is a high-severity issue affecting your dishwasher.
How do I fix Fisher & Paykel error code F1?
Tilt the DishDrawer backward so the base pan drains, then dry the pan completely with a towel Then, Reset power at the wall and start a short cycle to see whether the fault returns Then, If it returns, inspect the drain and fill hose fittings and the wash pump seal for a slow leak There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error F1?
Besides the error code on the display, common signs include: Both drawers dead or refusing to start; Water pooled under the cabinet; Drain pump running continuously. If you notice any of these symptoms, check your dishwasher's display panel for error code F1.
How much does it cost to fix Fisher & Paykel F1?
Repair costs for Fisher & Paykel F1 typically range from $150 to $400 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online