Want a regional phone & address? Pick your area.
Amana·Dishwashermedium severity
Amana Dishwasher Error Code F1E1
Temperature sensor fault
Common Causes
- 1NTC sensor failure
- 2Wiring fault
- 3Connector corrosion
Step-by-Step Troubleshooting
- 1
Locate the thermistor sensor in the sump area near the wash pump
- 2
Disconnect and measure resistance: approximately 55,000 ohms at 77F (25C)
- 3
An open circuit or near-zero reading confirms sensor failure
- 4
Trace the sump harness for breaks where it runs past the heat of the wash pump
Pro Diagnostic Tip
F1E1 on a budget Amana ADB dishwasher is a temperature-sensor loss: with no trustworthy water-temperature reading the control plays it safe and simply runs the wash for its maximum duration, which is why the telltale is a normal cycle that now drags past three hours. Measure the sump thermistor near 55,000 ohms at room temperature; an open or near-zero reading condemns it. Because the sump is a wet, warm spot, check the connector for corrosion before deciding the sensor bead itself has failed.
You Might Also Notice
- •Wash cycles run far longer than they used to
- •Water never feels as hot as the cycle promises
- •A normal cycle now stretches past three hours
- •Dishes come out under-sanitized
- •Heated-dry results are weaker than before
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$75–$175
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Thermistor sensor assemblySensor harness
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F1E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Amana error code F1E1 mean?
Amana error code F1E1 indicates: Temperature sensor fault. This is a medium-severity issue affecting your dishwasher.
How do I fix Amana error code F1E1?
Locate the thermistor sensor in the sump area near the wash pump Then, Disconnect and measure resistance: approximately 55,000 ohms at 77F (25C) Then, An open circuit or near-zero reading confirms sensor failure There are 1 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my dishwasher has error F1E1?
Besides the error code on the display, common signs include: Wash cycles run far longer than they used to; Water never feels as hot as the cycle promises; A normal cycle now stretches past three hours. If you notice any of these symptoms, check your dishwasher's display panel for error code F1E1.
How much does it cost to fix Amana F1E1?
Repair costs for Amana F1E1 typically range from $75 to $175 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online