The short answer
The reading F60 on this cooktop names the user interface. The documented wording sits in the table below; the ranking beneath it is what decides where to start. It remains safe to use as long as nothing starts or runs on its own.
The documented code and its meaning
Reference| Code | Meaning |
|---|---|
| F60 | There may be a problem with the User Interface (Touchpad), or the associated wiring. |
What you actually observe
- The cooktop will not start although the display is lit — The control is awake and is not receiving the command.
- The panel responds, then stops responding once it warms up — Temperature-dependent behaviour points at the connection rather than the panel.
- The display dims or brightens with no input — Worth reporting: it narrows the supply question on the interface side.
- NEAR MISS — the whole panel is dark — That is a supply or a control question, not an interface one.
Causes, most likely first on this cooktop
- A key held down by dirt, a spill residue or a warped overlay — The control times how long a key stays active, so anything holding one closed reports as a pressed key rather than as dirt.
- A failed membrane or touch zone behind the glass — Touch panels age unevenly, so a single unresponsive zone is far more common than a dead panel.
- The ribbon cable or plug between the interface and the control — Earlier work disturbs this connection more than any other in the chain, and it is the cheapest thing in it.
- A fault on the interface board itself — Last, because it is the part people buy first and the one least often actually responsible.
Check in this order, and why
- Clean the panel thoroughly and dry it before anything else — Residue is the single most common cause of this family and it costs nothing to rule out.
- Work through every key and note which answer — Knowing which zones answer tells a technician whether to suspect the panel or the control.
- Power down and back up, then repeat the key test — If the pattern of dead keys moves after a restart, the panel is not the fault; if it stays put, it is.
- Ask whether a spray cleaner has been used on the panel — Spray that runs under the edge of an overlay causes exactly this pattern days later.
What an owner can safely check
- Wipe the whole control surface damp and dry it fully — Use plain water or a mild soap solution, not a spray cleaner aimed at the panel, and dry the edges where liquid collects.
Tools: soft cloth, mild detergentAbout 10 min
- Make sure nothing is resting on or against the panel — A pan handle, a towel or a phone left on the controls holds a key active and produces this code with nothing broken.
About 2 min
- Drop the breaker for a minute, restore, and retest the keys — This tells a current fault apart from one the control is only remembering.
About 4 min
Before anything is opened
Safety
Before any panel comes off, unplug the appliance or switch off its breaker: a capacitor can hold a charge after the power is off. On most installations there is no plug: the cooktop is wired in, and the breaker is the isolation point. Treat the glass as hot well after the display says the zones are off. Leave the interlocking switches wired as they came. They exist to remove power at the moment it has to go.
When this stops being an owner job
This becomes a service call if the code returns after a careful clean and a full power-down. From there on it is a meter on a de-energised circuit, and nothing under the glass can be reached until the unit is lifted out of its cutout. Call sooner than that if you smell burning, see scorching around the control area, or the appliance trips the breaker when it starts — any one of those is a stop-now signal rather than a wait-and-see one.
Nearest error-code pages
What this page does not cover
What is written here about F60 comes from the code set shared across Maytag cooktop model lines on one control platform. It does not extend to earlier control generations that happen to display the same characters for a different condition. Wiring colours, pin assignments, torque values and part numbers are all left out on purpose: they are family-specific and belong on the page for that family. Where such a page exists, it is the more specific answer and takes precedence over this one; the linked index is where to find it.
Other Maytag cooktop codes
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
