The short answer
A Costway FP Dryer that stops before the load is dry, or runs long past the point it should have finished, is telling you about the relationship between what the machine senses and what is actually happening in the drum. Both ends of that relationship are checkable, and neither usually needs a part.
What you see on the FP family
- The cycle ends after a few minutes with a wet load — The machine believes the load is dry, which points at the moisture sensor rather than at heat or airflow.
- An automatic cycle runs far longer than it used to — The machine cannot reach the dryness it is waiting for, which is what a restricted exhaust looks like from the control side.
- The machine stops part way and will not resume until it cools — A thermal device opening on temperature. It is protection working, and the airflow cause is still there.
- Timed cycles work but automatic cycles do not — That isolates the fault to the sensing side, because a timed cycle ignores the sensor entirely.
Causes, most likely first on the FP family
- Restricted exhaust or lint path — Ranked first on the FP family — A cycle that never ends on these models is airflow until proven otherwise, and the duct is where that is decided. A machine that cannot exhaust cannot carry moisture away, so an automatic cycle keeps extending while the load stays damp. The same restriction eventually opens a thermal device and stops the machine outright.
- Overloading and load composition — Second — and worth testing with one deliberately small load before any part is considered. A drum packed too full tumbles instead of circulating, so the sensor bars meet only part of the load and heavy items shield light ones. Mixed loads of towels and shirts dry at completely different rates.
- Moisture sensor bars coated or misreading — Third — because it is free to test and free to fix. Two metal strips inside the drum read the conductivity of the tumbling load. Fabric-softener residue insulates them, so they read dry from the first minute and the cycle ends almost immediately.
- Thermistor, cycling thermostat or control board — Fourth — and the only group here that is a service call on these models. A thermistor reading low keeps the machine calling for heat it already has; a cycling thermostat that has drifted ends or extends cycles unpredictably. The board itself fails least often of the group.
- Body: With only 2 codes in the FP family the ranking below is taken over a short roster rather than over everything the brand sells, which is why the top of this list is not where the brand-generic article puts it.
Check in this order, and why
- 1. Run one small, uniform load as a control — Three or four similar items. It removes overloading and mixed fabrics from the picture in a single cycle.
- 2. Run the same load on a timed cycle instead — If a timed cycle dries it properly, the fault is on the sensing side and the heat is fine.
- 3. Wipe the moisture sensor bars with rubbing alcohol — They are the metal strips inside the drum. Softener residue insulates them and makes every load read dry.
- Body: The 2 codes in the FP family are close enough in layout that the order below holds across all of them; check the plate on your own unit against the table before you order anything.
Before you open anything
Safety
Unplug the appliance or switch off its breaker before removing any panel — a capacitor can hold a charge after the power is off. Clean the sensor bars with the machine off and the drum still, never with a cycle paused. Never bypass a thermal device to make a cycle complete: it opened because the machine was too hot, and lint is fuel.
Models in the FP family
Reference| Model number | Family key |
|---|---|
| FP11243US-WH | costway:dryer:fp |
| FP11244US-WH | costway:dryer:fp |
When to call a technician
Call when the sensor bars are clean, a small load behaves the same way, and the duct is clear — at that point it is the thermistor, a thermostat or the control, and all of them sit behind a panel on these models. Call sooner if the machine keeps stopping mid-cycle, because repeated thermal shutdowns mean an airflow restriction that has not been found yet.
Other FP dryer pages
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
