AVANTI Dishwasher: Abnormal Noise or Vibration
Most dishwasher noise is loading: something touching a spray arm, a light item flipped over, or cutlery vibrating against the rack. The ordering below is what makes this page worth reading on an Avanti dishwasher. This is a compact cabinet with very little air around its condenser, so clearance and ventilation outrank component failure. What ranks first here is something you can correct yourself in under an hour, which is the reason to work down the list in order rather than book a visit straight away.
What you are actually seeing
- Check your symptom against this list first. If none of it matches, the fault is on another page.
- A rhythmic knocking that follows the spray arm rotation.
- A grinding at the start and end of the cycle when the machine drains.
- A high-pitched whine throughout the wash.
- Rattling that changes when the load is rearranged.
- Not this fault: If the noise comes with poor cleaning, the spray arm is likely fouled — the cleaning-performance page covers it.
- Not this fault: If the noise happens only at the drain and nothing drains, work the drainage page.
Causes, in the order worth checking
- Ranked by how often each turns out to be the answer on an Avanti dishwasher. The order is the point: work down it and you will usually stop before the bottom.
- An item fouling the spray arm — Why: A knife handle through the rack, a pan handle overhanging, or a tall glass all stop or deflect the arm, and the knocking that results is the most common noise complaint by far.
- The machine is not level or not secured in its cabinet — Why: A dishwasher that is not screwed to the worktop or the cabinet sides vibrates against them, and the cabinetry amplifies what would otherwise be a quiet machine.
- Debris in the pump or the filter — Why: Glass fragments, fruit stones and bone chips get past the filter and rattle in the pump, producing a grinding at the drain phase specifically.
- Light items flipped over or cutlery touching — Why: Plastic items that lift in the spray and metal touching metal both rattle, and both stop entirely when the load is rearranged.
- Spray arm bearing or mounting worn — Why: An arm that no longer sits square wobbles and knocks the rack above or below it. It is a cheap part and an owner-visible fault.
What to check, and in what order
- Each step eliminates the largest branch of the tree for the least effort, which is why they run in this order rather than the order of the list above.
- Run the machine empty and listen. — Why: It separates loading noise from mechanical noise in one cycle and costs nothing.
- Spin both spray arms by hand. — Why: A fouled or wobbling arm is the most common cause and is confirmed in seconds.
- Lift the filter and look for glass and hard debris. — Why: It explains the drain-phase grinding, and the filter needs cleaning anyway.
Checks you can safely do yourself
- Stop at the first step that would put a meter on live terminals.
- Run a short cycle with the machine completely empty and note whether the noise is still present. — Tools: None
About 40 min
- Spin both spray arms by hand, checking for play at the mounting and for anything that touches as they turn. — Tools: None
About 10 min
- Twist out the filter and check the well beneath it for glass, stones and bone fragments. — Tools: Gloves, torch
About 20 min
- Reload with nothing overhanging a rack and nothing tall enough to reach the upper arm. — Tools: None
About 15 min
Before you touch anything
Safety
Unplug the appliance or switch off its breaker before removing any panel. A capacitor can hold a charge after the power is off. — Id: unplug-before-service
Switch off the dishwasher at its breaker before reaching into the filter well or removing the kick panel; many machines are hard-wired. Broken glass collects in the filter and in the pump housing, so wear gloves and use a torch rather than feeling around. A capacitor in the control can hold a charge after the power is off.
Where the owner checks end
A condition, not a recommendation. Call a technician when one of these is true, and not before.
When the noise is identical with the machine empty and does not change when anything is moved. When a grinding at the drain phase persists with a clean filter. When the spray arm mounting is worn and the arm has play. When the noise arrived with a loss of cleaning performance.
Sources
General guidance- 29 CFR 1910.147 — The Control of Hazardous Energy — US Occupational Safety and Health Administration, fetched 2026-09-06
Nearest pages of the same kind
What this page does not cover
Links down: - [Common AVANTI Dishwasher Problems](/blog/avanti-dishwasher-problems)
This page is generalized: it covers the Avanti dishwasher line as a whole and does not narrow to a family, a model number or a serial range. The use-and-care guide covers the owner-serviceable envelope; a full service manual is not generally published for these models, so diagnosis works from the symptom rather than from a published code chart. The overview at avanti-dishwasher-problems lists every problem class for this machine and routes down to the page for each; any family- or model-specific page that exists beneath this one is linked from there.
Other faults on this machine
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
