The short answer
Ice arriving slowly, hollow, fused into a block or not at all on the RA family is a temperature story far more often than a mechanism story, and that is where this page starts. An ice complaint on a cabinet like this splits in two before any diagnosis starts, because some of the models in the table make ice automatically and some do not, and the two versions of the fault have almost nothing in common.
What you observe on these models
- Trays that will not freeze through overnight — A tray takes longer than people expect, but a full night with no solid result means the compartment is not holding a low enough temperature.
- Water arriving but never freezing into shape — Where a model fills and then fails to release, the water is reaching the mould and the cold is not finishing the job in the time the cycle allows.
- Frost building inside where nothing should be frosting — On a cabinet with no ice maker this is what the complaint usually turns out to be, and it is a sealing and airflow story rather than an ice one.
- NEAR MISS - the ice maker is noisy but working — Filling and harvesting are both audible events on any model that has them, and a working cycle is not a fault however loud it sounds.
Causes, most likely first on this platform
- The compartment is not cold enough — Ice is nothing more than water held below freezing long enough, so every other cause on this page sits downstream of temperature. A compartment at 0 degrees Fahrenheit (minus 18 degrees Celsius) or below makes ice; one a few degrees warmer makes it slowly, hollow, or not at all. Across a group this wide fitment is the least predictable thing about it, so temperature - which applies to every entry - leads instead.
- Supply line, shutoff and fill valve — Second on this platform. Where the model is plumbed the supply is still worth proving, especially after a move, since a kinked line behind a cabinet stays invisible until the cabinet comes out.
- The model simply does not have one — Third here. Where a model never had an ice maker, there is no fault to find: the ice being complained about is frost, and warm air getting in is what makes it.
- The ice maker being switched off without anyone meaning to — Fourth. It stays worth a glance at any point: an arm resting up or a switch left off produces a total stoppage with nothing wrong at all.
- A frozen fill tube or a jammed cube — Last. A jam is worth clearing before condemning anything, and it is usually the visible consequence of a temperature swing rather than a fault in its own right.
Check in this order, and why
- Establish whether this model has an ice maker at all — Look for a mould, a bail arm and a fill tube rather than for a badge. If none of those are there, the rest of this page collapses into a temperature and sealing question. With 28 entries on 14 bases in the table below, this check is one of the few that means the same thing across all of them.
- Check the door is closing and the seal is intact — Warm humid air reaching a freezing compartment makes frost, softens ice and bridges cubes together, and it does all three before it makes the cabinet feel warm.
- Pull the cabinet out and follow the supply line — Where the model is plumbed, look for a shutoff that has been nudged, a kink behind the unit and a line that has been crushed against the wall. This is the check a move most often makes necessary.
Before you open anything
Safety
Isolate the cabinet at the plug or the breaker before a panel comes off, and never put a hand into a mechanism that is still live - an ice maker harvests on its own schedule, not yours. Where the model is plumbed, close the water shutoff before disturbing any fitting, and use warm water rather than a tool on any ice you need to clear.
Models in the RA family
Reference| Model number | Family key |
|---|---|
| RA10X0W-IS | avanti:refrigerator:ra |
| RA10X1B-IS | avanti:refrigerator:ra |
| RA10X3S-IS | avanti:refrigerator:ra |
| RA3106WT | avanti:refrigerator:ra |
| RA3116BT | avanti:refrigerator:ra |
| RA3136SST | avanti:refrigerator:ra |
| RA31B** | avanti:refrigerator:ra |
| RA31B0W | avanti:refrigerator:ra |
| RA31B1B | avanti:refrigerator:ra |
| RA31B3S | avanti:refrigerator:ra |
| RA32J0W | avanti:refrigerator:ra |
| RA32J1B | avanti:refrigerator:ra |
| RA32J3S | avanti:refrigerator:ra |
| RA45B3S | avanti:refrigerator:ra |
| RA7306WT | avanti:refrigerator:ra |
| RA7306WT-IS | avanti:refrigerator:ra |
| RA730B0W | avanti:refrigerator:ra |
| RA7316PST | avanti:refrigerator:ra |
| RA7316PST-IS | avanti:refrigerator:ra |
| RA731B1B | avanti:refrigerator:ra |
| RA7326BT | avanti:refrigerator:ra |
| RA7326BT-IS | avanti:refrigerator:ra |
| RA733B3S | avanti:refrigerator:ra |
| RA75**** | avanti:refrigerator:ra |
| RA75V** | avanti:refrigerator:ra |
| RA75V0W | avanti:refrigerator:ra |
| RA75V1B | avanti:refrigerator:ra |
| RA75V3S | avanti:refrigerator:ra |
When to call a technician
Bring someone in once the free checks are clean and the mechanism still will not cycle, because the remaining causes need a meter and a panel off. Do not wait at all if the cabinet has stopped holding temperature more generally, because at that point ice is the least of it and the food is the priority.
Other faults covered for these models
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
