The short answer
The ARC roster spans several capacity cores rather than one, so the cabinets it covers differ in how far air and meltwater have to travel inside them, and it lists two naming generations side by side, so cabinets of noticeably different ages share this page. The most common cause of no ice on a cabinet like this is not the ice maker at all. It is the supply to it, the temperature around it, or the arm and bin sensor that tell it to stop, and all three are reachable without tools.
What you observe on these models
- Ice fused into one block in the bin — Slow production, or a thaw and refreeze event. The cubes sat long enough to bond, which means production has been marginal for a while.
- The arm is up or the bin sensor is blocked — The mechanism has been told the bin is full and is doing exactly as instructed. It is the single most common non-fault on this list.
- Ice with an odour or a taste — A filter that is overdue, or cubes that have been sitting and absorbing what is around them. Neither is a mechanical fault.
- Production that stopped after the cabinet was moved — The supply line or the fill tube has shifted. Timing that specific points away from the mechanism entirely.
Causes, most likely first on the ARC line
- Shut-off arm raised or bin sensor blocked — Ranked first on this roster: nothing about the cabinet looks wrong in this case, which is why it survives so many self-diagnoses.
- The compartment is not cold enough to complete a cycle — Ranked second on this roster: the mechanism will not harvest until the mould reaches its release temperature, so a compartment that has drifted warm stops production while looking otherwise healthy.
- Water filter overdue and restricting flow — It ranks third here because it is cheap, scheduled maintenance that owners routinely defer, and because the symptom is so specific.
- Ice maker module or mould heater failed — Ranked last on this roster: reaching it honestly is a result, because it turns the question into whether the assembly is worth replacing.
- Body: The ranking here keeps the brand-generic order, and what the ARC line changes is the order of the checks beneath it: entries appear both with and without a revision digit, so a part that fits one cabinet on this roster may not fit its neighbour.
Check in this order, and why
- Establish which generation of this roster you have — Two naming generations are listed together here, so cabinets of noticeably different ages share this page. Which one you own changes what a worn part is likely to be.
- Look at the arm or sensor path before anything else — Lower a raised arm, clear anything sitting in front of a sensor, and give it a few hours.
- Look into the mould for standing water — Water present and not frozen means the temperature is the problem. Work the cooling fault instead.
- Check the filter age and that it is fully seated — Replace an overdue filter and re-seat a recent one. Then allow a day before judging the cube size.
Before you open anything
Safety
Switch off at the breaker before any panel comes off and before putting a hand into the ice maker housing, because the harvest mechanism moves under power and does not warn you. Close the household shut-off before touching a supply fitting; a line under pressure behind a heavy cabinet is difficult to stop once it starts. Use warm water on an ice plug, never a tool, and keep water away from the supply cord throughout.
Models in the ARC family
Reference| Model number | Family key |
|---|---|
| ARC035S0ARWW | arctic-king:refrigerator:arc |
| ARC04B2C** | arctic-king:refrigerator:arc |
| ARC04S1A** | arctic-king:refrigerator:arc |
| ARC050S0ARBB | arctic-king:refrigerator:arc |
| ARC050S0ARWW | arctic-king:refrigerator:arc |
| ARC05B2C** | arctic-king:refrigerator:arc |
| ARC05MW | arctic-king:refrigerator:arc |
| ARC05MW1 | arctic-king:refrigerator:arc |
| ARC070S0ARBB | arctic-king:refrigerator:arc |
| ARC070S0ARWW | arctic-king:refrigerator:arc |
| ARC07M3AWW | arctic-king:refrigerator:arc |
| ARC07MW1 | arctic-king:refrigerator:arc |
| ARC07MW2 | arctic-king:refrigerator:arc |
When to call a technician
Call when cubes form fully and never release, because that pattern points at the harvest side and nothing an owner can reach will change it. Call immediately if you find water anywhere around the supply fitting, and close the household shut-off before you do: a leaking supply behind a heavy cabinet does far more damage than a week without ice.
Nearest pages of this class
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
