Nothing at all from an Amama dishwasher points first at the supply and the latch, and both take a minute to check, in the field. The order below starts with no power at the outlet or a tripped breaker. Each check below either ends the problem or narrows it, and the page says which.
What it looks like from the outside
- Panel is dark and nothing responds — Worth knowing: many machines wake on the latch.
- Delay indicator showing on the display on an Amama dishwasher — A delay start explains a appliance that does nothing for hours, on the machines we see.
- Machine had a power cut recently — what it looks like — On this build, a full reset is the first move.
- Start button beeps then nothing happens — Nine times in ten, an acknowledged press with no action is a latch or lock answer.
- Breaker or protected outlet has tripped on an Amama dishwasher — On most units, inspect the panel before anything else.
- Panel lights but the cycle never begins — As a rule, power is present and something is refusing.
The causes, in likelihood order on an Amama dishwasher
- No power at the outlet or a tripped breaker — what it looks like — On this build, a tripped circuit or a switched outlet is a complete stop. Test the outlet with another appliance if it is accessible. It leads the order because it explains more of these calls than anything below it, and costs nothing to check.
- Control lock or delay start active — In practice, locks survive power cycles on most designs. Hold the lock button for a few seconds.
- Door not latched on an Amama dishwasher — Machines refuse to start until the latch reports closed, on the Amama builds this page covers. Listen for the latch and try start again. It falls here because the entries above it come up more often, though this one is far from rare.
- Held state after an interrupted cycle — In practice, a appliance stopped mid-cycle waits to be cleared before it will accept a new program. Record whether the trouble began after an interruption.
- Failed latch switch, keypad or board — what it looks like — On this build, it is reached by elimination. Test every button and note which respond. It sits at the bottom because it is reached by elimination rather than by symptom.
Where to look first
- First: no power at the outlet or a tripped breaker — It belongs at this point because the previous result is what makes this check meaningful. On any build of this kind, test the outlet with another appliance if it is accessible.
- Second: control lock or delay start active — It belongs at this point because the previous result is what makes this check meaningful. Read the panel for a lock or delay indicator.
- Third: door not latched — Listen for the latch and try start again. This check earns its place by being fast and by eliminating an costly possibility.
- Fourth: held state after an interrupted cycle — The position is deliberate: done earlier, the result would be ambiguous. Run cancel and drain, then remove power for a few minutes.
The owner checks, step by step
- Reset the machine — Worth knowing: switch the breaker off for a few minutes, restore it and try a standard program. Watch the panel wake for any code.
About 10 min
- Confirm the water supply — In the field, open the supply valve under the sink fully and listen for the fill after pressing start. A valve left half closed after plumbing work is common.
Tools: TorchAbout 10 min
- Close the door properly — From experience, this is the most common cause and takes seconds. Check nothing is proud of the racks, then close the door with a deliberate push.
About 5 min
- Read the panel carefully — Worth knowing: locks do not clear with a power cycle. Check for a padlock symbol and a delay countdown on the display.
About 5 min
What to do before any check
Safety
Nothing below is done with the circuit live. Unplug the appliance or switch off its breaker before removing any panel; a capacitor can hold a charge after the power is off. Do not use drain chemicals in the machine; they damage seals and plastic.
Owner fix or service call
Book a visit if the breaker trips whenever the appliance is energised, and leave the circuit off until then. When the page runs out of owner checks, the remaining causes need a meter and a technician.
Standards cited on this page
General guidance- Manufacturer service manuals; OSHA control of hazardous energy standard — Manufacturer service manuals; OSHA control of hazardous energy standard, fetched
Related pages on other brands
What this page does not cover
This page covers the class rather than the model. Panel layouts, code lists and part numbers vary within the same brand. The order of causes shifts with build and installation, and those shifts are noted in the ranking rather than hidden in it. A more specific page for a particular Amama family or model does not exist yet. When it does, this page will link down to it and defer to it. The other problem pages for this appliance are indexed at amama-dishwasher-problems.
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
