Want a regional phone & address? Pick your area.
LG·ovenhigh severity
LG Error Code F11
Communication error
Common Causes
- 1Board communication failure
Step-by-Step Troubleshooting
- 1
Power cycle the oven by turning off the circuit breaker for 10 minutes — communication bus errors between the UI board and relay board can clear on full reset
- 2
On LG double ovens and combination units, F11 indicates the upper and lower control boards have lost serial communication
- 3
Check the ribbon cable or wire harness connecting the display board to the relay/power board — reseat both connectors firmly
- 4
Inspect for loose or corroded pins at the board connectors — oven heat can cause solder joints to develop cold cracks over years of thermal cycling
- 5
If the cable and connectors are intact, one of the two boards has a failed communication transceiver — swap boards one at a time to isolate
Pro Diagnostic Tip
LG double ovens and smart ovens use I2C or SPI serial buses between the boards. Power surges can latch up the communication controller ICs without visible damage. A full 10-minute power-off reset (not just the oven power button) clears the latched state in approximately 40% of F11 cases.
You Might Also Notice
- •Display blank or frozen
- •Oven not responding to any inputs
- •One cavity works but the other does not (double ovens)
- •ThinQ app cannot connect to oven
Parts, Cost & Difficulty
Repair Difficulty
Professional OnlyEstimated Repair Cost
$220–$420
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
EBR84433508 (Oven Control Board — UI)EBR84433509 (Relay/Power Board)EAD63928907 (Communication Wire Harness)
Do You Have the Right Tools?
Combustion analyzer ($300), igniter tester ($120), temperature calibrator ($150), and gas pressure manometer. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
Gas ovens involve live gas lines — a loose connection creates explosion and carbon monoxide risk. Electric ovens run on 240V circuits. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Get Professional Help Now
Error code F11 is a high-severity issue that can cause further damage to your oven if left unresolved. A licensed technician can diagnose and fix it the same day.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
$89 → $0 Service Call & Diagnosis — offer ends May 31
Frequently Asked Questions
What does LG error code F11 mean?
LG error code F11 indicates: Communication error. This is a high-severity issue affecting your oven.
How do I fix LG error code F11?
Power cycle the oven by turning off the circuit breaker for 10 minutes — communication bus errors between the UI board and relay board can clear on full reset Then, On LG double ovens and combination units, F11 indicates the upper and lower control boards have lost serial communication Then, Check the ribbon cable or wire harness connecting the display board to the relay/power board — reseat both connectors firmly There are 2 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my oven has error F11?
Besides the error code on the display, common signs include: Display blank or frozen; Oven not responding to any inputs; One cavity works but the other does not (double ovens). If you notice any of these symptoms, check your oven's display panel for error code F11.
How much does it cost to fix LG F11?
Repair costs for LG F11 typically range from $220 to $420 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.