Want a regional phone & address? Pick your area.
Kenmore·Dishwashermedium severity
Kenmore Dishwasher Error Code F9E1
Drain timeout
Common Causes
- 1Drain hose kinked
- 2Disposal knockout in place
- 3Drain pump weak
- 4Air gap clogged
Step-by-Step Troubleshooting
- 1
Check the drain hose for kinks or clogs along its entire length
- 2
If connected to disposal, verify the knockout plug was removed
- 3
Clean the air gap cap if installed — remove cap and clear debris
- 4
Clean the drain filter inside the tub thoroughly
Pro Diagnostic Tip
This Whirlpool-platform 665-prefix Kenmore draws a line between a slow drain and a dead pump: this timeout means the pump runs but water leaves too slowly, whereas the pump-fault code means it never runs at all. A slow drain points at a kinked hose, a clogged filter, or a partly-blocked air gap rather than the pump.
You Might Also Notice
- •A little water still standing when the cycle ends
- •The drain step crawling on far too long
- •A gurgle at the air gap while it pumps out
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$75–$225
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
W10876600 drain pump
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Check drain hose and disposer connection
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F9E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Kenmore error code F9E1 mean?
Kenmore error code F9E1 indicates: Drain timeout. This is a medium-severity issue affecting your dishwasher.
How do I fix Kenmore error code F9E1?
Check the drain hose for kinks or clogs along its entire length Then, If connected to disposal, verify the knockout plug was removed Then, Clean the air gap cap if installed — remove cap and clear debris There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error F9E1?
Besides the error code on the display, common signs include: A little water still standing when the cycle ends; The drain step crawling on far too long; A gurgle at the air gap while it pumps out. If you notice any of these symptoms, check your dishwasher's display panel for error code F9E1.
How much does it cost to fix Kenmore F9E1?
Repair costs for Kenmore F9E1 typically range from $75 to $225 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online