Want a regional phone & address? Pick your area.
Haier·Washermedium severity
Haier Washer Error Code E4
Heating fault — water or drying air not heating
Common Causes
- 1Heating element open or scaled
- 2NTC thermistor out of range
- 3Element wiring or connector failed
- 4Board heater relay fault
Step-by-Step Troubleshooting
- 1
Unplug the washer and remove the rear or lower panel to reach the heating element
- 2
Inspect the element for heavy scale, blistering, or a burnt terminal
- 3
Measure element resistance across the terminals — an open reading means a failed element
- 4
Check the companion NTC thermistor resistance and its wiring back to the board
- 5
Replace the failed element or thermistor and its gasket as identified by the tests
Pro Diagnostic Tip
On combo washer-dryers E4 can point at either the wash heater or the drying heater. Note whether it appears during the wash or the dry phase to target the right element.
You Might Also Notice
- •Cold wash water
- •Laundry stays damp after a dry cycle
- •Long cycle times
Parts, Cost & Difficulty
Repair Difficulty
Hard — Advanced Skills RequiredEstimated Repair Cost
$120–$280
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Heating elementNTC thermistorElement gasket
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E4 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Haier error code E4 mean?
Haier error code E4 indicates: Heating fault — water or drying air not heating. This is a medium-severity issue affecting your washer.
How do I fix Haier error code E4?
Unplug the washer and remove the rear or lower panel to reach the heating element Then, Inspect the element for heavy scale, blistering, or a burnt terminal Then, Measure element resistance across the terminals — an open reading means a failed element There are 2 more steps — see the full troubleshooting guide above. This repair typically requires professional tools and expertise.
How do I know if my washer has error E4?
Besides the error code on the display, common signs include: Cold wash water; Laundry stays damp after a dry cycle; Long cycle times. If you notice any of these symptoms, check your washer's display panel for error code E4.
How much does it cost to fix Haier E4?
Repair costs for Haier E4 typically range from $120 to $280 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online