Want a regional phone & address? Pick your area.
Haier·Washermedium severity
Haier Washer Error Code E2
Drain fault — water not pumped out in time
Common Causes
- 1Drain filter clogged with lint or coins
- 2Drain hose kinked or standpipe too high
- 3Pump impeller jammed
- 4Drain pump failed
Step-by-Step Troubleshooting
- 1
Open the lower front access flap, set out towels and a shallow pan, and slowly unscrew the drain filter
- 2
Clear lint, coins, and hair, then feel the housing for a jammed impeller
- 3
Straighten the drain hose and confirm the standpipe height is within the manual range
- 4
Run a spin-and-drain — a pump humming with no flow has a jammed or failed impeller
- 5
Replace the drain pump if it is silent or the impeller spins freely without pumping water
Pro Diagnostic Tip
On compact Haier washers the pump is small and clogs faster than a full-size machine. Clean the filter monthly if the household washes pet bedding or lint-heavy loads.
You Might Also Notice
- •Water left in the drum
- •Cycle stops before spin
- •Slow or partial draining
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$100–$235
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Drain pump assemblyDrain pump filter
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Clean the drain pump filter behind the lower flap
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code E2 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Haier error code E2 mean?
Haier error code E2 indicates: Drain fault — water not pumped out in time. This is a medium-severity issue affecting your washer.
How do I fix Haier error code E2?
Open the lower front access flap, set out towels and a shallow pan, and slowly unscrew the drain filter Then, Clear lint, coins, and hair, then feel the housing for a jammed impeller Then, Straighten the drain hose and confirm the standpipe height is within the manual range There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my washer has error E2?
Besides the error code on the display, common signs include: Water left in the drum; Cycle stops before spin; Slow or partial draining. If you notice any of these symptoms, check your washer's display panel for error code E2.
How much does it cost to fix Haier E2?
Repair costs for Haier E2 typically range from $100 to $235 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online