Want a regional phone & address? Pick your area.
GE·Oven / Rangemedium severity
GE Error Code FD
Meat probe shorted
Common Causes
- 1Contaminated probe jack
- 2Damaged probe wire
- 3Faulty meat probe
Do not use a damaged meat probe — exposed wiring inside the oven cavity is a shock hazard at 120V. Replace the probe rather than repair it.
Step-by-Step Troubleshooting
- 1
Remove the meat probe from the oven jack
- 2
Clean the probe jack inside the oven with a dry cotton swab — grease buildup is the top cause
- 3
Inspect the probe cable for cuts, kinks, or melted insulation
- 4
Test probe resistance at room temp — should read around 50k ohms
- 5
If resistance reads near 0, the probe is internally shorted — replace it
- 6
If probe tests good but FD persists, the jack or ERC probe circuit is faulty
Pro Diagnostic Tip
FD only appears when the oven detects the probe circuit is completed (shorted). If no probe is inserted and FD still shows, the jack receptacle has internal contamination or a short. Clean with electrical contact cleaner first before replacing the jack.
You Might Also Notice
- •Oven will not heat with probe inserted
- •Temperature display shows probe temp when no probe is present
- •FD appears during preheating
Parts, Cost & Difficulty
Repair Difficulty
Easy — DIY FriendlyEstimated Repair Cost
$30–$150
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
WB20X10025 meat probeWB24X29252 probe jack receptacle
Do You Have the Right Tools?
Combustion analyzer ($300), igniter tester ($120), temperature calibrator ($150), and gas pressure manometer. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Remove meat probe and check for contamination
This repair requires combustion analyzers, gas pressure manometers, and temperature calibration instruments. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
Gas ovens involve live gas lines — a loose connection creates explosion and carbon monoxide risk. Electric ovens run on 240V circuits. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code FD disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
$89 → $0 Service Call & Diagnosis — offer ends May 31
Frequently Asked Questions
What does GE error code FD mean?
GE error code FD indicates: Meat probe shorted. This is a medium-severity issue affecting your oven / range.
How do I fix GE error code FD?
Remove the meat probe from the oven jack Then, Clean the probe jack inside the oven with a dry cotton swab — grease buildup is the top cause Then, Inspect the probe cable for cuts, kinks, or melted insulation There are 3 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my oven / range has error FD?
Besides the error code on the display, common signs include: Oven will not heat with probe inserted; Temperature display shows probe temp when no probe is present; FD appears during preheating. If you notice any of these symptoms, check your oven / range's display panel for error code FD.
How much does it cost to fix GE FD?
Repair costs for GE FD typically range from $30 to $150 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.