Expert advice, troubleshooting guides, and maintenance tips for all your appliances
5,493 articles
Or call (415) 795-7300

Whirlpool Dryer PF error code — power failure interrupted the cycle. A senior technician explains what to check, when to call a pro, typical pricing, and how to weigh repair against a new machine.

F0 on a Whirlpool oven is a stuck function-key fault, often from self-clean heat warping the overlay. How to reset it and the repair cost.

F1 on a Whirlpool oven is a touch-pad or clock fault. Why the oven stops heating, how to reset it, and what the repair costs.

F2 on a Whirlpool oven is an over-temperature safety code — a fire hazard. Why a welded bake relay is usually to blame, safety steps, and cost.

F3 on a Whirlpool oven is a shorted temperature-sensor fault. Why the RTD sensor fails, how it differs from F4, and the affordable repair cost.

F4 on a Whirlpool oven is an open temperature-sensor fault. Why a loose rear plug often mimics a dead probe, and the affordable repair cost.

F5 on a Whirlpool oven is a control watchdog / hardware fault. Why it is usually a board failure, when surge protection helps, and the repair cost.

F9 on a Whirlpool oven is a door-latch fault, usually after self-clean. Why the latch gears strip, the cool-down trick, and the repair cost.

CF on a Whirlpool refrigerator is a communication failure between the boards. Why the door-hinge harness is usually to blame, food-safety steps, and cost.

PO on a Whirlpool refrigerator is a power-outage reminder, not a fault. What it means for food safety, how to clear it, and when a UPS helps.

F0E1 on a Whirlpool washer: the Clean Washer cycle sensed a load in the drum. What it means, how to clear it yourself, and when a sensor calibration is worth it.

F0E2 on a Whirlpool washer means overload detected. Why the drum is reading too heavy, how to fix it yourself, and when a worn sensor is to blame.

F0E5 on a Whirlpool washer flags a load imbalance during spin. How to redistribute and level the machine, and when tired suspension is the real cause.

F1E1 on a Whirlpool washer is a motor control error, usually surge-related. Why the drive board fails, the safety risk, and whether repair is worth it.

F1E2 on a Whirlpool washer is a drive-motor error. What it means, the safe checks you can do, and whether a $300-plus motor repair is worth it.

F2E1 on a Whirlpool washer is a stuck-key or interface fault. Why the touch panel misreads, how to reset it, and the water-intrusion cause behind repeats.

F3E1 on a Whirlpool washer is a water-level sensor fault. Why the analog transducer misreads, the overfill risk, and why descaling the sump comes first.

Whirlpool Washer F3E2 error code — water temperature sensor fault. A senior technician explains what to check, when to call a pro, typical pricing, and how to weigh repair against a new machine.

F5E1 on a Whirlpool washer is a door-switch fault — the control cannot confirm the door is closed. How to test the strike and switch, and repair cost.

F5E2 on a Whirlpool washer is a door-lock error. Why the wax-motor latch wears out, how to tell it from a switch fault, and what the repair costs.

F5E3 on a Whirlpool top-load washer is a lid-lock error. Why the motorized cam strips, how to spot it, and the cost to replace the lid-lock module.

Whirlpool Washer F6E1 error code — central control communication error. A senior technician explains what to check, when to call a pro, typical pricing, and how to weigh repair against a new machine.

F7E1 on a Whirlpool washer is a motor speed-sensor fault. Why mechanical drag mimics a bad sensor, the hand-spin test, and the cost to repair.

F8E1 on a Whirlpool washer is a long-fill / water-supply fault. Why it is a flow-rate problem, the supply checks to run, and repair cost.

Whirlpool Washer F8E2 error code — dispenser system fault. A senior technician explains what to check, when to call a pro, typical pricing, and how to weigh repair against a new machine.

F8E3 on a Whirlpool washer is an overflow code and a flood risk. Why the inlet valve or pressure switch fails, the safety steps, and repair cost.

F9E1 on a Whirlpool washer is a long-drain fault. Why the coin trap and drain pump are the usual causes, the sound test, and repair cost.

HC on a Whirlpool washer means the hot and cold hoses are reversed. Why it happens after installation, how to fix it in minutes, and when a thermistor is at fault.

Sud on a Whirlpool washer means excessive suds. Why non-HE detergent and overdosing cause it, how to fix it, and when a slow drain is the real issue.

Whirlpool Washer uL error code — unbalanced load during spin. A senior technician explains what to check, when to call a pro, typical pricing, and how to weigh repair against a new machine.
Let our professional technicians help. Same-day service available.