The short answer
On an LG oven, the first thing to check is a control board or relay fault. An oven that will not heat divides sharply into two faults: one that heats nothing at all, and one that heats to the wrong temperature. LG ovens are display-led: the board watches the oven sensor closely and will show a fault before the cavity is noticeably wrong. Decide which you have before anything is ordered, because the causes barely overlap.
What you observe
- The oven never gets warm at all — No heat in any mode points at the element, the igniter or the supply.
- It heats but takes far longer than it used to — Slow heating with eventual success points at measurement or at a door that leaks.
- Baking is uneven front to back or top to bottom — Uneven results usually mean airflow or one of two elements rather than a total failure.
- NEAR MISS - the cooktop works but the oven does not — On a range these are separate circuits, so a working cooktop tells you nothing about the oven supply.
Causes, most likely first on LG
- A control board or relay fault — Relays on the board switch the elements. Ranked first because it explains an oven that ignores one mode while another works, but it ranks below the visible causes. On LG, the board holds the cavity tightly to the oven sensor, so sensor drift becomes a visible baking fault quickly.
- An oven sensor reading the cavity wrongly — The sensor probe in the cavity tells the board the temperature. Ranked second because it decides what the control believes the temperature is, so it produces every symptom except a dead oven.
- A failed bake element or gas igniter — An electric element breaks its coil, often with a visible blister or break. Ranked third because it carries the full load every cycle and it is the part that ages out first.
Check in this order, and why
- Try bake and broil separately and note which works — One mode working and the other not points at the control or at that element specifically. It comes first because the ranking above puts a control board or relay fault ahead of everything else on this platform.
- Put an oven thermometer in the centre and compare with the setting — A consistent gap between the set point and the reading is a sensor or calibration symptom.
- Set the oven to bake and look for the element glowing — A bake element that never glows red, or a gas burner that never lights while the igniter glows, is the diagnosis.
What an owner can safely check
- Measure the cavity with an oven thermometer — Place a separate oven thermometer on the centre shelf, preheat to a normal baking temperature, and give it time to settle before comparing it with the setting.
Tools: oven thermometerAbout 45 min
- Set a plain bake temperature and watch the element or burner — With the oven empty and cold, select bake at a normal temperature and watch through the door for the element glowing or the burner lighting within a few minutes.
Tools: torchAbout 15 min
- STOP HERE if the next check needs a meter on live terminals — Everything past this point is measured with power applied, and that is where an owner check ends and a service call begins.
Before you open anything
Safety
Switch the oven off at its breaker before removing any panel or touching an element - a capacitor can hold a charge after the power is off, and an oven cavity stays hot long after it is switched off. If this is a gas oven and you smell gas, do not operate any switch: leave the building and call the gas utility or emergency services from outside. Never line the oven floor with foil: it blocks airflow and overheats the cavity.
When to call a technician
Call once the element has been seen not to glow, the breaker has been fully reset, or the cavity measures a consistent margin away from the setting - all three of those are measured or replaced with the panel off. Call a gas technician rather than testing anything yourself on a gas oven that will not light, and call at once for any smell of gas or any scorching around the terminals.
Nearest pages of this class
What this page does not cover
This page covers the LG oven as a class, not one family or one model line. What changes from build to build - wiring colours, part numbers and component test values - is deliberately absent. Where your model plate names a line, use that line's documentation first.
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
