The short answer
On Fohere an ice maker that has stopped is most often an ice maker switched off, or none fitted at all. Ranked that way because there is no forced air in the fresh-food space at all, so every fault that begins with a fan is off the table before you start.
What you observe
- The mould is full of ice that never drops — Filling works and harvesting does not, which is a much shorter list.
- Ice arrives, but far more slowly than it used to — A gradual decline usually means a filter or a valve rather than a sudden failure.
- NEAR MISS: there is water on the floor as well as no ice — Then you have a supply leak, and that page is the one to read first. Shut the supply valve before anything else.
Causes, most likely first on Fohere
- The ice maker is switched off, or there is not one fitted — First on a machine this size, where the owner is close to every part of it. The bail arm gets lifted by a bag of frozen food, or a panel switch gets pressed during a clean, and the machine dutifully stops. Plenty of cabinets in this class ship with a manual tray and no automatic maker at all, which is not a fault.
- The freezer is not cold enough to trigger a harvest — Second: on a small machine this is quick to confirm and quick to rule out. The maker will not eject until its mould reaches its release temperature. A freezer holds food safely at 0 degrees Fahrenheit or below, and a compartment sitting above that will keep food frozen while never quite triggering a harvest.
- The water supply is off, kinked or barely open — Third. A shutoff valve half closed after other work, a supply line crushed behind the cabinet when it was last pushed back, or a saddle valve that was never opened properly.
- The ice maker module, ejector or mould heater has failed — Last, and it is the reason the order above matters. The mould fills and never releases, or the motor never turns.
Check in this order, and why
- Look at the bail arm or the on-screen ice setting — It is the one check that can end the diagnosis in seconds, so it goes first whatever else is true.
- Put a thermometer in the freezer overnight and read it in the morning — It separates an ice-maker fault from a refrigeration fault with one measurement.
- Trace the supply line from the valve to the cabinet and look for kinks — A crushed line behind the unit is common and completely invisible from the front.
What an owner can safely check
- Check the bail arm is down, or that the ice setting is on — Clear any food touching the arm.
About 5 min
- Leave an appliance thermometer in the freezer overnight — A freezer holds food safely at 0 degrees Fahrenheit or below.
Tools: appliance thermometerAbout 15 min
- Find the shutoff valve, confirm it is fully open, then ease the cabinet out and inspect the line — Look for a sharp bend where the cabinet was pushed back against the line.
Tools: torchAbout 20 min
- STOP HERE if the next step needs a meter on live terminals — That is where an owner check ends and a service call begins.
Before you open anything
Safety
Shut the water supply valve before disconnecting any line, and have a towel and a bowl ready because the line stays charged after the valve closes. Unplug the appliance or switch off its breaker before removing any panel near the ice maker. Never thaw a frozen fill tube with a flame, a heat gun or a naked bulb: the liner and the tube are plastic and they will deform long before the ice gives up.
When to call a technician
Call when the supply is proven good, the freezer is cold enough and the mould still will not release, because that puts the fault in the module and it is replaced as an assembly. Call sooner if you find water anywhere it should not be, or if the freezer is sitting warm, because then the ice is a symptom of something larger and the cold matters more than the cubes do.
Nearest pages of this class
What this page does not cover
This page covers the brand and the refrigerator class, not one family or model line. Where a family-specific or model-specific page exists for your unit, that page is the more specific answer and it takes precedence over this one. Not here: part numbers, wiring colours and component locations, which differ by family.
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
