The short answer
On a Danby Premiere freezer, why there is no ice, or bad ice comes down to a short list, and on this line the order is not the generic one. The diagnosis starts at a cabinet not cold enough to trigger a harvest, because the mould thermostat will not release until the mould is cold enough, so a marginal cabinet makes no ice rather than slow ice. The first three checks below need no tools and no parts; the point at which this stops being an owner job is stated further down, as a condition rather than as a recommendation.
What you are seeing
- The ice maker in an upright cabinet has not cycled in days and the bin is empty.
- Cubes are small, hollow or fused into a single block.
- Ice smells or tastes of stored food.
- The mould fills and never releases, or releases and never fills.
- Water freezes in the fill tube before it reaches the mould.
- Frost is building on the freezer walls and there is no ice maker at all.
- Note: Near-miss symptoms that mean a different fault: If the whole cabinet is soft, the cooling failure comes first and the ice follows it. If water is reaching the floor, read the leak page. On a manual-defrost cabinet with no ice maker, an ice complaint is usually a frost complaint.
Causes, ranked for a Danby Premiere freezer
- A cabinet not cold enough to trigger a harvest — Why this rank: The mould thermostat will not release until the mould is cold enough, so a marginal cabinet makes no ice rather than slow ice.
- A garage, basement or utility room outside the cabinet’s climate rating — Why this rank: This line ends up in unheated and unconditioned spaces far more often than the compacts do, and an out-of-rating room produces this complaint on a cabinet with nothing wrong with it.
- Ice fusing because the bin is not being used — Why this rank: Cubes sublimate and re-freeze into a block, which is a usage pattern rather than a fault.
- A frozen fill tube — Why this rank: The tube is the coldest point on the water path, so a slow fill turns to ice there before anywhere else.
- The bail arm or shut-off left off — Why this rank: It is free to check, it is knocked up by stored food, and it stops production as completely as any failure.
- Frost build-up on a manual-defrost cabinet mistaken for an ice fault — Why this rank: Most cabinets in this class have no ice maker, so the ice being complained about is the frost that needs defrosting.
What to check, in order
- Confirm the cabinet is holding 0 °F (−18 °C) or below with a thermometer in the load. — Order: First — Why: Below that threshold nothing harvests, and no ice maker work is worth doing until it is met.
- Check the bail arm or shut-off and clear anything holding it up. — Order: Second — Why: It is the cheapest cause on the list and it accounts for a large share of no-ice calls.
- Look at the fill tube where it enters the mould for a plug of ice. — Order: Third — Why: It is visible without tools and it explains a mould that never fills while the valve works perfectly.
- Run the manual harvest test from the manual and listen for the valve buzzing as the mould fills. — Order: Fourth — Why: It exercises the whole circuit in one cycle and shows exactly which stage stops.
Steps a homeowner can take
- Unplug the appliance or switch off its breaker before removing the ice maker or a panel. — Tools: none — Time: a moment
- Confirm the bail arm is down and nothing is holding it up. — Tools: none — Time: a moment
- Put a thermometer in the load, close the cabinet, and read it after several hours. — Tools: thermometer — Time: overnight
- Empty the bin of fused ice, leave it out for a cycle and watch what the ice maker does. — Tools: none — Time: half an hour or so
- Melt a frozen fill tube with a hair dryer on low, keeping the heat moving and off the plastic. — Tools: hair dryer, towels — Time: half an hour or so
- If the cabinet is manual-defrost with no ice maker, defrost it fully and dry it before restarting. — Tools: towels, cooler — Time: overnight
Before you start
Safety
Unplug the appliance or switch off its breaker before removing the ice maker or any panel. A capacitor can hold a charge after the power is off. Never chip ice from a mould or a bin with a metal tool — the mould heater and the water tubing sit directly behind it. Shut the water supply off at its valve before disturbing any fitting.
When this stops being an owner job
Call when the cabinet holds 0 °F (−18 °C), the bail arm is on, the fill tube is clear and the mould still will not fill, or when it fills and never harvests. Testing a valve or a mould heater means metering a live circuit.
Sources
General guidance- The control of hazardous energy (lockout/tagout), and manufacturer service-manual practice — OSHA 1910.147 / manufacturer service manuals, fetched 2026-09-06
- Refrigeration and Food Safety — USDA Food Safety and Inspection Service, fetched 2026-09-06
Nearest pages
Generalized information
This page is generalized: it covers Danby Premiere across the whole freezer range rather than one family or one model group. It does not cover model-level pages for individual Danby Premiere cabinets, which do not exist in this reference yet; when they do, they will be linked from here. Until then, check the rating plate for your model group before ordering any part, because that is what the ranking above cannot narrow for you.
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
