The short answer
On a Danby dryer, a water leak most often comes back to condensate hose or its connection loose. Danby is a Canadian maker that specialises in compact, portable and apartment-scale appliances, so its units end up in garages, basements, dorms, offices and second kitchens far more often than in a fitted main kitchen. The brand moves one thing in particular: machine out of level so water misses the sump ranks higher here than it otherwise would. The first two checks below are owner work and need no tools beyond what is already in the house.
What you observe
- Water on the floor under a condenser or ventless machine
- Water dripping from the door or the base at the end of a cycle
- Damp at the back of the machine near a drain hose
- Water inside the drum at the start of a cycle
- A wet patch that appears only on long cycles
Ranked for a Danby dryer
- Condensate hose or its connection loose — Why this rank: On a ventless machine the condensate hose is the only water carrier there is, and a loose clamp or a hose pulled off during a move puts every drop on the floor. — Owner checkable: true
- Machine out of level so water misses the sump — Why this rank: The internal channels are shallow; a tilted machine sends water past them onto the floor. — Owner checkable: true
- Condensate tank cracked or not seated — Why this rank: A tank that has been dropped or is sitting proud overflows into the cabinet, and the water appears at the front. — Owner checkable: true
- Condenser clogged so condensate overflows its channel — Why this rank: When the heat exchanger cannot drain, water backs up and finds the easiest way out of the cabinet. — Owner checkable: true
Check in this order
- Trace the hose from the machine to the tank or drain and check every connection. — Because: It sits at rank 1 on this brand.
- Level the machine in both directions. — Because: It sits at rank 2 on this brand.
- Remove the tank, check it for cracks and refit it squarely. — Because: It sits at rank 3 on this brand.
- Remove and rinse the condenser unit. — Because: It sits at rank 4 on this brand.
Steps a homeowner can safely take
- Establish what kind of machine you have — a vented dryer produces no condensate of its own, so water beneath it usually comes from elsewhere. — Tools: model label
About 10 min
- Dry the floor completely and run a cycle, noting when and where fresh water appears. — Tools: towels, paper towel — Time: 1 cycle
- Remove the condensate tank, check it for cracks, wipe its seat and refit it squarely until it clicks. — Tools: cloth
About 15 min
- Remove the condenser unit as the manual describes and rinse it thoroughly, then refit it dry. — Tools: running water
About 30 min
- Unplug the machine and check the condensate hose and every clamp from the machine to the tank or drain. — Tools: flashlight, screwdriver
About 25 min
- Level the machine in both directions and confirm it does not rock. — Tools: spirit level, adjustable wrench
About 25 min
- Stop condition: Stop at the first step that would require a meter on live terminals.
Before you open anything
Safety
Unplug the appliance or switch off its breaker before removing any panel. A capacitor can hold a charge after the power is off. Nothing on this page asks you to work at a live terminal, and none of it asks you to defeat a door interlock or a safety switch — those exist to stop the machine running in a state that can injure you, and a machine that will not run with its door open is working correctly. If a breaker trips twice on the same operation, leave it off: a repeat trip is a fault to be found, not a nuisance to be reset. Stop at the first step that would need a meter on live terminals. unplug-before-service branch-circuit-15-20a
Owner fix or service call
Water appears only at the end of a cycle, which points at the pump or its housing The tank, condenser and hose are all confirmed sound and water is still arriving Water has reached an outlet, a power strip or a cord — unplug and keep the machine off A vented machine is producing water with nothing above or behind it to explain it
Nearest pages of the same kind
Generalized information
This page is generalized across the Danby dryer range: no model-specific wiring diagrams, no part numbers, no service-manual procedure for any individual unit. Where your model differs, the model documentation wins. model-specific wiring diagrams part numbers service-manual procedures
Danby dryer
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
