Error Codes repair guides and troubleshooting tips.
462 articles

Frigidaire refrigerator 5Y EF means the evaporator fan is not running — the same alarm as SY EF (the display draws an S like a 5). Usually ice from a defrost...

Frigidaire refrigerator OP is a freezer over-temperature event flag — usually a door left ajar or a power blip. It self-recovers within a day.

Frigidaire refrigerator SY CF is a condenser fan circuit failure — the compressor-deck fan stalled, often just packed with pet hair and dust.

Frigidaire refrigerator SY EF is an evaporator fan circuit failure — the board got no confirmation the circulation fan spun. Often an iced-in blade from a...

Frigidaire washer E13 means a water leak detected in the tub — the base-pan float tripped. Read the drip location: a rear bearing seal is costly.

Frigidaire washer E21 is a drain time exceeded — the sump did not empty in time. Usually a lint-matted coin-trap filter or a jammed impeller.

Frigidaire washer E44 is a door lock detection failure — the bolt throws but the control never hears that it did. A lost-signal fault in the switch, wire.

Frigidaire washer E54 is a motor relay failure on the control board — the relay welded shut, usually because a shorted motor overdrew it. Ohm the motor...

Frigidaire washer E57 is an inverter high-current fault — the drive electronics tripped on overcurrent. Often a shorted motor, sometimes a blown inverter stage.

Frigidaire washer EF1 is a clogged drain hose — the pump is fine but the outlet line is blocked or kinked. Flush the hose. An easy, mostly free DIY fix.

Frigidaire washer EF2 is excessive suds detected — too much or the wrong detergent for a low-water front-loader. No parts needed: cut the dose and use HE...

GE oven or range showing F8? The ERC control board has failed. Learn the safe reset, warning signs, likely parts, and F8 repair cost.

GE washer showing E8? It senses an overflow — usually a stuck inlet valve or pressure switch. Safe checks, likely parts, and E8 repair cost.

F1E1 on a JennAir Dishwasher means water temperature sensor (thermistor) open. Repair cost $90–$220: likely causes, DIY checks, and when to call a technician.

F1E2 on a JennAir Dishwasher means water temperature sensor (thermistor) shorted. Repair cost $90–$220, likely causes, and safe DIY checks.

F2E1 on a JennAir Dishwasher means stuck key / user interface fault. Repair cost $130–$290, likely causes, safe DIY checks, and when to call a technician.

JennAir dishwasher panel dark or resetting on its own with an F2E2 code? The user-interface board has faulted. Learn the ribbon reseat that often fixes it, and what it costs.

F3E1 on a JennAir Dishwasher means optical water indicator (owi) sensor fault. Repair cost $110–$260: likely causes, DIY checks, and when to call a technician.

JennAir dishwasher won't start, or quits within seconds, with an F5E1 code? The door switch is not confirming closed. Learn the latch checks, the panel-ready clue, and the cost.

JennAir dishwasher door springing back open, or blocked by the rack, with an F5E2 code? The door cannot reach the latched position. Learn the quick rack check and the repair cost.

JennAir dishwasher over- or under-filling with an F6E4 code during the fill? The flow meter is miscounting. Learn why hard water is usually to blame and what the repair costs.

F7E1 on a JennAir Dishwasher means wash (circulation) motor fault. Repair cost $180–$420, likely causes, safe DIY checks, and when to call a technician.

F8E1 on a JennAir Dishwasher means slow or insufficient water fill. Repair cost $120–$300, likely causes, safe DIY checks, and when to call a technician.

F1E0 on a JennAir Oven/Range means control board eeprom read / write failure. Repair cost $225–$475: likely causes, DIY checks, and when to call a technician.

F2E0 on a JennAir Oven/Range means shorted keypad (touchpad). Repair cost $150–$350, likely causes, safe DIY checks, and when to call a technician.

F2E1 on a JennAir Oven/Range means keypad ribbon disconnected or unresponsive. Repair cost $130–$300: likely causes, DIY checks, and when to call a technician.

F3E0 on a JennAir Oven/Range means oven temperature sensor open. Repair cost $75–$190, likely causes, safe DIY checks, and when to call a technician.

F3E2 on a JennAir Oven/Range means oven temperature sensor shorted. Repair cost $75–$195, likely causes, safe DIY checks, and when to call a technician.

F5E1 on a JennAir Oven/Range means self-clean door lock will not lock. Repair cost $140–$300, likely causes, safe DIY checks, and when to call a technician.

F5E2 on a JennAir Oven/Range means self-clean door lock will not unlock. Repair cost $140–$300, likely causes, safe DIY checks, and when to call a technician.