What is the Bosch Dishwasher E07 error?
E07 on a Bosch dishwasher is a CrystalDry fan-motor fault — the small fan that drives hot air through the zeolite drying mineral has stalled or lost its signal, so the board flags the drying system. Because E07 only touches drying, the wash still runs normally; the giveaway is a load that comes out clean but wet. That also makes it a non-urgent code: you can keep washing if you do not mind towel-drying. The first thing worth doing is a full breaker reset for a few minutes, since a one-time glitch can post E07, but a genuinely stalled fan or corroded connector will bring it right back.
E07 on a Bosch Dishwasher: likely causes and repair cost
On a Bosch Dishwasher, the E07 code signals: crystal dry fan motor error.
| Likely cause | Typical likelihood |
|---|---|
| Fan motor failure | Most common |
| Fan blade obstruction | Common |
| Wiring issue | Less common |
Difficulty: hard · usually a technician job
Symptoms that often accompany E07: Dishes are wet after the drying cycle; No airflow sound during the dry phase; Extended cycle times waiting on dry; Condensation left standing in the tub; Wash performance normal but drying fails
Technician diagnostic sequence for E07:
- Access fan motor through inner door panel
- Spin fan blade by hand — should rotate freely without grinding
- Measure motor winding resistance
- Check connector at fan motor for corrosion from steam exposure
Parts a technician may check or replace: CrystalDry fan motor; fan blade assembly
Field note: E07 is the CrystalDry fan-motor fault (Bosch 800+ and Siemens PerfectDry are the same zeolith system) — the fan that pushes hot air through the zeolite mineral has stalled or lost its signal. Steam corrosion at the fan-motor connector is the number-one failure mode, so, with the dishwasher unplugged, resolder or reseat that connector before buying a motor. Because E07 only touches drying, the wash still runs normally and the giveaway is a load that comes out wet even though it cleaned fine — quite different from E01, where the heat-pump motor stops the cycle outright.
How to troubleshoot the E07 error yourself
Since the causes in the table above are a stalled fan motor, a blocked blade, or a wiring fault, DIY is limited to a reset and a listen. Switch the dishwasher off at the breaker for several minutes, restore power, and run a cycle with a dry-heavy load — if E07 clears and stays gone, it was transient. During the dry phase, listen for the fan: silence where you would expect a soft airflow sound confirms the motor is not spinning. The number-one real cause on these units is steam corrosion at the fan-motor connector, which sits right in the drying airflow, so if you are handy, with the dishwasher unplugged, the connector is worth reseating and drying before any part is bought — a corroded plug mimics a dead motor. Do not dismantle the inner door panel to reach the CrystalDry fan behind the door insulation; that, and replacing the motor, is a technician job. If a reset and a connector check do not restore drying, call one.
Rather have a pro handle it?
A vetted local technician can come out and diagnose your dishwasher at home.
Is the Bosch Dishwasher E07 error worth fixing?
E07 is worth fixing on most Bosch dishwashers, and sometimes it costs very little. CrystalDry machines were premium purchases, so the repair sits well below half the price of a comparable replacement — a clear repair on any unit that still washes cleanly. Replacement only makes sense on a very old machine where the fan motor failure joins other problems and the total climbs. But on its own, on a sound Bosch, E07 is a contained drying-system repair that brings back the genuinely dry cycles these units are known for.
Bosch Dishwasher E07: frequently asked questions
What does the E07 error mean on a Bosch Dishwasher?
E07 means the CrystalDry fan motor — the fan that pushes hot air through the zeolite drying mineral — has stalled or lost its signal, so the board flags the drying system. The wash itself is unaffected.
Is it safe to keep using a Bosch Dishwasher that shows the E07 error?
Yes, it is safe to keep washing. E07 is a drying-only fault with no water or electrical hazard, so the machine still cleans; you will simply get wet dishes at the end until the fan is repaired.
Can I clear the E07 error myself, or do I need a technician?
You can try a few-minute breaker reset and, if you are handy, unplug the appliance or switch off its breaker, then reseat the fan-motor connector where steam corrosion collects. Replacing the fan motor behind the inner door panel is a technician job.
Which parts usually fail when a dishwasher throws the E07 code?
The CrystalDry fan motor is the usual failure, very often because of steam corrosion at its connector rather than the motor windings themselves. A blocked fan blade or a chafed wire are the next suspects.
Why does fan motor failure trigger the E07 error?
The fan drives hot air through the zeolite mineral during drying while the board watches its feedback. When the motor stalls or the corroded connector breaks the signal, the board loses the fan and raises E07 to flag that drying can no longer run.


