The short answer
On an Amana washer, the first thing to check is an unbalanced load or an unlevel machine. A washer makes different noises at wash and at spin, and which half of the cycle the noise belongs to narrows the cause immediately. Amana washers are the simplest machine in their family - a plain suspension, a plain transmission and very little electronics between you and the fault. Note whether it grinds at wash, roars at spin, or bangs only when the load gathers on one side.
What you observe
- A loud roar or rumble that rises with the spin — Noise that tracks spin speed points at the bearing or the drum support.
- Banging or walking during the spin — A machine that moves across the floor is unbalanced, not broken.
- A grinding or scraping at the wash stage — Noise during the slow wash action points at the drive or something trapped in the drum.
- NEAR MISS - a click or clunk as the cycle changes stage — Valves opening and the drive changing direction click by design on most machines.
Causes, most likely first on Amana
- An unbalanced load or an unlevel machine — A heavy item gathering on one side throws the drum out of balance, and a machine that rocks on its feet turns that into banging and walking. Ranked first because it is free to correct and it produces the most alarming noise on the list. On Amana, there is very little between the drum and the cabinet on this platform, so a mechanical cause reaches your ears directly.
- An object trapped between drum and tub — Coins, clips and underwires pass through the drum holes and rattle in the outer tub. Ranked second because coins and underwires reach the gap constantly, and it is the cheapest cause on the list to settle.
- A drain pump with debris in the impeller — Buttons, grit and hair reach the pump and rattle against the impeller. Ranked third because the pump runs only at drain, so a noise confined to that stage identifies it immediately.
- A worn belt, pulley or drive coupling — A glazed belt squeals under a heavy load, and a worn coupling on a direct-drive platform grinds at the wash stage while spinning almost silently. Ranked fourth on this platform.
Check in this order, and why
- Redistribute the load and rock the cabinet by hand — A machine that moves under hand pressure will bang at spin no matter what else is true. It comes first because the ranking above puts an unbalanced load or an unlevel machine ahead of everything else on this platform.
- Spin the empty drum by hand and listen for something loose — A rattle with an empty drum and no water is almost always a trapped object.
- Note whether the noise happens only while water is leaving — A noise confined to the drain stage is the pump or its filter.
What an owner can safely check
- Level the machine and rebalance the load — Spread the load evenly around the drum, then adjust the feet until the cabinet sits solid with no rock at any corner and the lock nuts are tight.
Tools: adjustable spanner, spirit levelAbout 25 min
- Run an empty spin and listen, then check pockets — Run a short empty spin cycle and listen for rattling, and make a habit of emptying pockets - most trapped objects arrive that way.
About 15 min
- STOP HERE if the next check needs a meter on live terminals — Everything past this point is measured with power applied, and that is where an owner check ends and a service call begins.
Before you open anything
Safety
Switch the machine off at the breaker before opening any panel or reaching into the pump filter - a capacitor can hold a charge after the power is off. Expect water when you open a pump filter, and lay towels first. A washer is extremely heavy with water in it: never tip or move a loaded machine, and get help even when it is empty.
When to call a technician
Call once the load, the levelling and the pump filter are eliminated and the noise rises with the spin, because a bearing or a suspension job means opening the machine and is not a first repair. Call sooner if the noise arrived with water under the machine, since a bearing that has failed often takes its seal with it.
Nearest pages of this class
What this page does not cover
This page covers the Amana washer as a class, not one family or one model line. What changes from build to build - wiring colours, part numbers and component test values - is deliberately absent. Where your model plate names a line, use that line's documentation first.
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
