The short answer
On the Amana 7w7p41 refrigerator family, an ice maker that has stopped filling the bucket points at the cabinet rather than the maker, because on a platform where the ice maker shares the freezer air, anything that warms that air stops the ice first. The brand-generic article puts the ice maker module itself at the top of this symptom. It does not lead here, and on these models it is not what the first three checks are looking for.
What you observe on these models
- Production has slowed rather than stopped — A gradual decline is a supply story; an abrupt stop usually is not.
- The bucket is empty and the maker never runs — Nothing cycles, nothing fills, and the cabinet is otherwise behaving normally.
- Cubes come out thin, hollow or half formed — A short fill rather than a failed harvest, which points at water rather than at the module.
- NEAR MISS — the dispenser works but the maker does not — Water reaching the door proves the supply and moves the ranking on.
Causes, most likely first on this family
- Freezer not cold enough to finish a harvest — First on this platform. The maker waits for the mould to reach its harvest temperature. A freezer sitting a few degrees warm never gets there, so the ice stops without a single ice-maker part being faulty.
- Shutoff arm or ice-level sensor holding the maker off — Second on these models. A bail arm nudged up by a bag of frozen food, or a beam sensor blocked by frost, tells the maker the bucket is full. It is the fastest thing on this list to check and the most often missed.
- Low water pressure at the valve, or a clogged filter — Third, and less common than the two above. The maker fills on a timed valve opening rather than to a level, so anything that slows the water gives a short fill. The result is thin crescents and a bucket that never fills.
- Humid air reaching the bucket and frosting it into a block — Fourth, and the least common of the four here. A gasket that no longer seals at one corner lets the bucket frost over. The maker keeps cycling and the ice keeps welding itself together.
Check in this order, and why
- Put a thermometer in the freezer and leave it overnight — Start here. A freezer sitting warm stops the harvest, and the ice maker is then a symptom rather than the fault.
- Look at the shutoff arm or the sensor window — Then this. An arm nudged up by a bag, or a frosted window, stops a healthy maker instantly and costs nothing to correct.
- Fill a cup at the dispenser if the cabinet has one, or watch a fill — Third. A slow or hesitant flow is a supply problem, and it explains thin ice without any part being faulty.
Before you open anything
Safety
Unplug the appliance or switch off its breaker before removing any panel; a capacitor can hold a charge after the power is off.
Models covered by the 7w7p41 family
Reference| Model number | Family key |
|---|---|
| 7W7P41-01 | amana:refrigerator:7w7p41 |
| 7W7P41-02 | amana:refrigerator:7w7p41 |
| 7W7P41-03 | amana:refrigerator:7w7p41 |
| 7w7P41-04 | amana:refrigerator:7w7p41 |
| 7w7P41-05 | amana:refrigerator:7w7p41 |
| 7w7P41-06 | amana:refrigerator:7w7p41 |
| 7w7P41-07 | amana:refrigerator:7w7p41 |
| 7w7P41-08 | amana:refrigerator:7w7p41 |
| 7w7P41-09 | amana:refrigerator:7w7p41 |
| 7w7P41-10 | amana:refrigerator:7w7p41 |
| 7w7P41-11 | amana:refrigerator:7w7p41 |
| 7w7P41-12 | amana:refrigerator:7w7p41 |
| 7w7P41-13 | amana:refrigerator:7w7p41 |
| 7w7P41-14 | amana:refrigerator:7w7p41 |
| 7w7P41-15 | amana:refrigerator:7w7p41 |
| 7w7P41-16 | amana:refrigerator:7w7p41 |
| 7w7P41-17 | amana:refrigerator:7w7p41 |
| 7w7P41-18 | amana:refrigerator:7w7p41 |
| 7w7P41-19 | amana:refrigerator:7w7p41 |
| 7w7P41-20 | amana:refrigerator:7w7p41 |
| 7w7P41-21 | amana:refrigerator:7w7p41 |
| 7w7P41-22 | amana:refrigerator:7w7p41 |
| 7w7P41-23 | amana:refrigerator:7w7p41 |
| 7w7P41-24 | amana:refrigerator:7w7p41 |
| 7w7P41-25 | amana:refrigerator:7w7p41 |
| 7w7P41-26 | amana:refrigerator:7w7p41 |
| 7w7P41-27 | amana:refrigerator:7w7p41 |
| 7w7P41-28 | amana:refrigerator:7w7p41 |
| 7w7P41-29 | amana:refrigerator:7w7p41 |
| 7w7P41-30 | amana:refrigerator:7w7p41 |
| 7w7P41-31 | amana:refrigerator:7w7p41 |
| 7w7P41-32 | amana:refrigerator:7w7p41 |
| 7w7P41-33 | amana:refrigerator:7w7p41 |
| 7w7P41-34 | amana:refrigerator:7w7p41 |
| 7w7P41-35 | amana:refrigerator:7w7p41 |
| 7w7P41-36 | amana:refrigerator:7w7p41 |
| 7w7P41-37 | amana:refrigerator:7w7p41 |
| 7w7P41-38 | amana:refrigerator:7w7p41 |
| 7w7P41-39 | amana:refrigerator:7w7p41 |
| 7w7P41-40 | amana:refrigerator:7w7p41 |
| 7w7P41-41 | amana:refrigerator:7w7p41 |
| 7w7P41-42 | amana:refrigerator:7w7p41 |
| 7w7P41-43 | amana:refrigerator:7w7p41 |
| 7w7P41-44 | amana:refrigerator:7w7p41 |
| 7w7P41-45 | amana:refrigerator:7w7p41 |
| 7w7P41-46 | amana:refrigerator:7w7p41 |
| 7w7P41-47 | amana:refrigerator:7w7p41 |
| 7w7P41-48 | amana:refrigerator:7w7p41 |
| 7w7P41-49 | amana:refrigerator:7w7p41 |
When to call a technician
Call once the supply, the shutoff arm, the bucket and the freezer temperature are all proven good, because what is left is the module or the valve. Call before cutting into any water line. A saddle valve on a supply pipe is the single commonest cause of a repair that turns into a plumbing job.
The other faults covered for this family
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
