The short answer
A 4w3n80 ice maker that has stopped is far more often a supply problem than a mechanical one. Where the brand-generic article opens with the module, this one opens with the fill tube, because on this platform that is the part that freezes first. Look in the mould before you order anything.
What you actually observe
- Ice sitting in the mould that never drops — That is a different half of the list entirely.
- A single fused block instead of loose cubes — Empty and dry it before deciding anything.
- A buzz from the back every few hours with no water — The valve is being asked to fill and cannot.
- NEAR MISS — no ice and the freezer is also warm — Then this is a cooling fault and the ice is only the symptom that showed first.
Causes on the 4w3n80 listings, most likely first
- A frozen fill tube — The tube that carries water to the mould sits in the coldest part of the cabinet, and once a dribble freezes in it nothing else gets through. A tube that has iced over gives a perfectly healthy ice maker with nothing to work with. The long revision run above covers a lot of production, and the oldest listings in it reach this point first.
- A clogged or wrongly seated water filter — A cartridge past its life throttles the flow enough that the mould fills short, and a short fill makes hollow cubes before it makes none. It is the cheapest thing on the list and the most often overdue.
- A failing water inlet valve — The valve opens for a few seconds per cycle, and a weak solenoid or a silted screen turns that into a trickle.
- A freezer that is not cold enough to harvest — The mould thermostat will not release a batch until the ice is genuinely hard, so a freezer sitting a few degrees warm stalls the whole cycle.
Check in this order, and why
- Look into the mould, not into the bin — Dry mould and iced mould send you to opposite halves of this list, and nothing else distinguishes them.
- Check the bail arm or the level sensor is clear — It is free, it takes a second, and it is the single most common reason a working ice maker stops.
- Confirm the freezer is actually cold enough — The harvest will not release until the ice is hard, so a warm compartment stalls a perfectly good ice maker.
- Follow the supply line behind the cabinet — You are looking for a kink against the wall and for a valve that was never fully reopened.
Before you open anything
Safety
Unplug the appliance or switch off its breaker before removing any panel. A capacitor can hold a charge after the power is off. Use warm water rather than heat to clear ice from a fill tube; a heat gun will melt the tube and the liner behind it. A freezer holds food safely at 0 °F (−18 °C) or below, so work quickly with the door open or move the contents first.
Models in the 4w3n80 family — 26 listings spanning a long revision run; the suffix marks production date rather than a change of mechanism.
Reference| Model number | Family key |
|---|---|
| 4w3n80-04 | amana:refrigerator:4w3n80 |
| 4w3n80-05 | amana:refrigerator:4w3n80 |
| 4w3n80-06 | amana:refrigerator:4w3n80 |
| 4w3n80-07 | amana:refrigerator:4w3n80 |
| 4w3n80-08 | amana:refrigerator:4w3n80 |
| 4w3n80-09 | amana:refrigerator:4w3n80 |
| 4w3n80-10 | amana:refrigerator:4w3n80 |
| 4w3n80-11 | amana:refrigerator:4w3n80 |
| 4w3n80-12 | amana:refrigerator:4w3n80 |
| 4w3n80-13 | amana:refrigerator:4w3n80 |
| 4w3n80-14 | amana:refrigerator:4w3n80 |
| 4w3n80-15 | amana:refrigerator:4w3n80 |
| 4w3n80-16 | amana:refrigerator:4w3n80 |
| 4w3n80-17 | amana:refrigerator:4w3n80 |
| 4w3n80-18 | amana:refrigerator:4w3n80 |
| 4w3n80-19 | amana:refrigerator:4w3n80 |
| 4w3n80-20 | amana:refrigerator:4w3n80 |
| 4w3n80-21 | amana:refrigerator:4w3n80 |
| 4w3n80-22 | amana:refrigerator:4w3n80 |
| 4w3n80-23 | amana:refrigerator:4w3n80 |
| 4w3n80-24 | amana:refrigerator:4w3n80 |
| 4w3n80-25 | amana:refrigerator:4w3n80 |
| 4w3n80-26 | amana:refrigerator:4w3n80 |
| 4w3n80-27 | amana:refrigerator:4w3n80 |
| 4w3n80-28 | amana:refrigerator:4w3n80 |
| 4w3n80-29 | amana:refrigerator:4w3n80 |
When to call a technician
Thawing a frozen fill tube, replacing a filter and freeing a stuck bin are owner jobs and between them they cover most ice faults. Replacing the module, the mould heater or the valve is not, because all three need the unit moved or the freezer stripped.
The other symptoms covered for this family
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
