The short answer for this line
On the ADB line the first split is between a dark panel and a lit one. A machine that accepts a cycle and never begins it is almost always the door telling it not to, and the two lead to different halves of the list. The first check on this line is the simplest one - close the door deliberately and listen for the latch - and the cause at the bottom of the list is the only one that is not owner work.
What this looks like on these models
- Some buttons respond and others do not — A pattern across the panel rather than a dead machine, which points at the membrane.
- It hums briefly and stops — Something is being attempted and abandoned, which is different from nothing happening at all.
- It worked until the breaker was reset — A machine dead since electrical work elsewhere is a supply question first.
- NEAR MISS - it runs but leaves the dishes dirty — A machine that completes a cycle has started; wash results are covered by the cleaning page for this line.
Causes in likelihood order on this platform
- The door latch not making — First here, and by a wide margin: this is first because it explains the exact complaint - a machine that accepts a cycle and never starts it - and because it is confirmed by closing the door differently.
- A door that no longer closes square — Second on this line: hinges that have worn, a machine that has settled out of level or a cabinet that has moved all stop the door meeting the frame squarely. The latch is fine; it simply cannot reach.
- A control lock or a delay left set — It ranks with the free checks because it is the commonest reason a working machine appears dead, especially after cleaning or after a child has been at the panel.
- The control board or the touch panel — Last on the list, and the only one here that is not owner work: a panel that responds to nothing, or that lights and accepts nothing, points at the control or its membrane. This is the last cause on the list because it is both the least likely and the most expensive to be wrong about.
Check in this order, and why
- Close the door deliberately and listen for the latch — Check nothing in the racks is proud of the frame and stopping the door from closing fully.
- Try starting it while holding the door home — Press the door firmly at the latch and start a cycle. A machine that runs while it is held is telling you about alignment, not electronics.
- Read the panel for a lock or a delay — Try the documented button-hold that clears the lock, then start a cycle again.
Safety first
Safety
Isolate the machine at the breaker before any cover comes off, because a capacitor can hold a charge after the power is off. Never defeat a lock or an interlock to test a cycle; they are the only things stopping the machine running with the door open.
Models in the ADB family
Reference| Model number | Family key |
|---|---|
| ADB1100AW**-02 | amana:dishwasher:adb |
| ADB1300AF** | amana:dishwasher:adb |
| ADB1300AF**-05 | amana:dishwasher:adb |
| ADB1300AF**-06 | amana:dishwasher:adb |
| ADB1300AF**-07 | amana:dishwasher:adb |
| ADB1300AF**-08 | amana:dishwasher:adb |
| ADB1300AF**-09 | amana:dishwasher:adb |
| ADB1300AF**-10 | amana:dishwasher:adb |
| ADB1300AF**-11 | amana:dishwasher:adb |
| ADB1300AF**-12 | amana:dishwasher:adb |
| ADB1300AF**-13 | amana:dishwasher:adb |
| ADB1300AF**-14 | amana:dishwasher:adb |
| ADB1400AG** | amana:dishwasher:adb |
| ADB1400AM** | amana:dishwasher:adb |
| ADB1400AM**-01 | amana:dishwasher:adb |
| ADB1400AM**-02 | amana:dishwasher:adb |
| ADB1400AM**-03 | amana:dishwasher:adb |
| ADB1500AD** | amana:dishwasher:adb |
| ADB1500AD**-01 | amana:dishwasher:adb |
| ADB1500AD**-02 | amana:dishwasher:adb |
| ADB1500AD**-03 | amana:dishwasher:adb |
| ADB1500AD**-04 | amana:dishwasher:adb |
| ADB1500AD**-05 | amana:dishwasher:adb |
| ADB1500AD**-06 | amana:dishwasher:adb |
| ADB1500AM** | amana:dishwasher:adb |
| ADB1700AD** | amana:dishwasher:adb |
| ADB1700AD**-02 | amana:dishwasher:adb |
| ADB1700AD**-03 | amana:dishwasher:adb |
The line between a fix and a call
Owner work is the panel, the door, the breaker and the supply valve. A dead machine with power proven at the outlet, or a panel that responds to nothing, is a technician job and not a parts guess.
The rest of this line
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
