The short answer
Two different complaints arrive under this heading on the Alpicool KID refrigerator: too little ice, on models that make it, and too much ice, on models that do not. The model record for this family is a single code, KID75, so everything below applies to one build rather than to a range of them. Decide which of the two you have before reading any further, because the causes below are ranked for both and they have almost nothing in common.
What you observe
- The maker runs its cycle and nothing comes out — Noise on schedule, an empty mould: the machine is being asked and has nothing to work with.
- Cubes are hollow, small, or stuck together in a lump — A mould that is not cold enough, or ice that has been sitting long enough to fuse.
- A sheet of ice across the bottom of the cabinet — Flat and clear rather than feathery — meltwater that refroze where it stood.
- NEAR MISS — the cabinet is also failing to hold temperature — Then this is a cooling fault first. Work the cooling page for this family; the ice is a symptom of it.
Causes, most likely first on this family
- Meltwater that cannot leave, refreezing into a slab — First. Water that cannot leave freezes where it stands, and the next cycle adds another layer. The result is a flat clear sheet rather than feathery frost, and it comes back as fast as it is cleared until the drain is dealt with. The record holds only KID75, so this check is the whole of the family's exposure to that cause.
- Damp air getting in and freezing where it lands — Second. Where the complaint is too much ice rather than too little, the source is almost always air. Every opening, and every hour a seal does not grip, brings moisture that freezes on the coldest plate — which is why the build-up is always thickest nearest the cold and nearest the leak.
- The ice maker switched off, or told the bin is full — Last. Every ice maker has a way of being turned off and a way of sensing a full bin, and both of them fail towards "make no more ice". A wire arm held up by a bag, a bin pushed in crooked, or a control left off after a clean will stop production with nothing broken at all.
- Body: With one code recorded there is no older or newer build here to tell apart. Nothing in the record splits these codes by drain arrangement, so it is treated as common to all of them — and a drain that has stopped draining turns every defrost into another layer of ice, which is why it is checked before the seal and long before anything is replaced.
First, second, third
- Thaw everything, clear the drain, then time the return — Warm water down the drain, dry it all out, and note how long the ice takes to come back. Days means drainage; months means ordinary use. On KID75 that is the whole of this step.
- Test the seal and count the openings — A strip of paper round the seal finds the leak path; a lid that gets opened every few minutes in a warm room needs no fault at all to ice up.
- Body: The record holds one code for this family, so the order below is not a model matrix — it is the order in which these causes can be eliminated on the machine in front of you, cheapest and least invasive first.
Before you open anything
Safety
Unplug the cabinet or switch off its breaker before removing any panel — a capacitor can hold a charge after the power is off. Never chip ice off with a knife or a screwdriver: the plate beneath it is thin and the tubing behind that is under pressure, so a slip ends the machine rather than the ice. Thaw it out instead, with the door open and a towel down.
Models this page covers — The one model code recorded for this family.
Reference| Model number | Family key |
|---|---|
| KID75 | alpicool:refrigerator:kid |
The line between a fix and a service call
Hand it over when the two cheap answers — the setting and the seal — have been eliminated and the ice is still winning, or when a maker that has water and cold still turns out nothing. Do not keep clearing ice weekly as a way of living with it: the same ingress that makes the ice is costing you cooling every hour of every day.
Other faults covered for this family
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
