What this usually is on these models
On the Alpicool ENX refrigerator a complaint that reads as "it runs but nothing is cold" is far more often heat that cannot leave the condenser than a failed compressor. The three codes in this family share the ENX prefix and differ only in what follows it, running from ENX42 to ENX62.
What the owner actually sees
- It is plainly running, and nothing inside is cold — The compressor note is there and the panel is lit; the contents disagree with both.
- It never stops running — A healthy cabinet cycles. One that runs from morning to night is one that is never reaching the number it was set to.
- It pulls down overnight and gives it all back by the afternoon — That pattern points at the room and at the seal, not at the refrigeration.
- NEAR MISS — it is silent and dark — Nothing lit, nothing running: that is a power or start fault and belongs on a different page from this one.
What it usually turns out to be, in order
- Heat that cannot leave the condenser — First. The condenser is the cabinet's only way of getting rid of what it has taken out of the food, and it needs moving air to do it. Tucked into a recess or wedged against a wall, it ends up re-breathing its own exhaust: the heat goes round in a circle, the run never ends and the setpoint is never met. The same check covers everything from ENX42 to ENX62; the record gives no reason to treat those codes differently here.
- The supply the cabinet is running from — Second. A compressor draws several times its running current for the moment it starts. A thin extension lead, a tired socket or a long run sags at exactly that moment, the control sees the dip and shuts down to protect itself, and tries again a minute later. The panel stays lit throughout, which is why this gets mistaken for a dead cooling system.
- A loss in the sealed system — Last, always. It is the rarest of these causes and the only one that cannot be touched without recovery equipment and a licence. What it looks like is a machine trying hard and achieving nothing: long runs, a condenser that stays lukewarm, and a cabinet that drifts back up as fast as it comes down.
- Body: Three codes, one ENX prefix, ENX42 at one end and ENX62 at the other. The record does not say what the numbers track, but a family carried across this many codes is sold in more than one variant, and more variants means more different places these end up standing in — recesses and cupboards among them. That is what moves airflow above the supply path here.
Check in this order, and why
- Give it a hand's width on every side and run it for an hour — Watch whether the compressor starts cycling rather than running flat out. Recovery in open air is an installation verdict, not a repair. Identical on every code from ENX42 to ENX62.
- Plug it into a different socket, directly — No adaptor, no extension, nothing else on the same outlet. A machine that cools properly on the new socket has told you the fault was never inside it.
- Body: Work these in order rather than picking the one that sounds most likely. Each check below removes a whole branch of the list above, and none of them needs a panel off or a tool in hand.
Safety first
Safety
Unplug the cabinet or switch off its breaker before removing any panel, and remember that a capacitor can hold a charge after the power is off. Nothing in this order requires getting inside. Never put a heat source near the coil to hurry a thaw, and never puncture frost with a knife or a screwdriver: the plate under it is thin, and what runs behind it is under pressure.
Models this page covers — The three model codes recorded for this family; the record carries no column separating them.
Reference| Model number | Family key |
|---|---|
| ENX42 | alpicool:refrigerator:enx |
| ENX52 | alpicool:refrigerator:enx |
| ENX62 | alpicool:refrigerator:enx |
When to call a technician
Call once the checks above are clean: a cabinet on a sound supply, in open air, with a seal that grips and a setpoint you have set yourself, has a fault worth paying to diagnose. Call straight away, without working the list, if you can smell burning, if the compressor is tripping the protection in the room, or if there is oil anywhere on the tubing — oil outside the pipework means the system is open, and every hour it runs after that costs more to put right.
Other faults covered for this family
Lead Appliance Repair Technician · 12 years experience
Experienced technician with 12 years specializing in washing machine and dryer repairs across all major brands.
