Want a regional phone & address? Pick your area.
Maytag·Dryerlow severity
Maytag Dryer Error Code PF
Power failure interrupted the cycle
Common Causes
- 1Momentary utility outage mid-cycle
- 2A tripped or half-seated dryer breaker
- 3A loose 240V cord or terminal-block lug
- 4Power dropped when another large appliance cycled on the same circuit
Step-by-Step Troubleshooting
- 1
Press Start to pick the cycle back up; on a Maytag Bravos or Maxima the control stores the interrupted program and this code simply flags that the power blinked
- 2
If it will not resume, open the breaker panel and cycle the double-pole dryer breaker fully off then on to reseat a half-tripped pole
- 3
Check the four-prong or three-prong cord where it lands on the terminal block for a browned or loose lug that drops power under load
- 4
Note whether the fault appears only when the furnace or another heavy load kicks on, which points at a shared or undersized circuit rather than the dryer
Pro Diagnostic Tip
This code records a power interruption, not an internal dryer fault, so a single occurrence after a storm needs no repair. One that returns every few loads is the tell — chase a loose terminal-block lug or a fatigued breaker before suspecting the control, since the Maytag board only reports the loss, it does not cause it.
You Might Also Notice
- •The dryer stops mid-cycle and shows the code on power-up
- •The clock or settings reset after the stop
- •The fault follows a storm or a brief blackout
- •It recurs when another appliance starts on the same line
Parts, Cost & Difficulty
Repair Difficulty
Easy — DIY FriendlyEstimated Repair Cost
$0–$200
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Power cordTerminal block
Do You Have the Right Tools?
Gas leak detector ($130), thermal fuse tester ($95), belt tension gauge, and vent inspection camera ($180). Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Press Start to resume, or restart the cycle
This repair requires gas leak detectors, thermal fuse testers, and high-voltage multimeters. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
Gas dryers carry carbon monoxide and explosion risk. Even electric dryers involve 240V circuits that can deliver a fatal shock. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code PF disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does Maytag error code PF mean?
Maytag error code PF indicates: Power failure interrupted the cycle. This is a low-severity issue affecting your dryer.
How do I fix Maytag error code PF?
Press Start to pick the cycle back up; on a Maytag Bravos or Maxima the control stores the interrupted program and this code simply flags that the power blinked Then, If it will not resume, open the breaker panel and cycle the double-pole dryer breaker fully off then on to reseat a half-tripped pole Then, Check the four-prong or three-prong cord where it lands on the terminal block for a browned or loose lug that drops power under load There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dryer has error PF?
Besides the error code on the display, common signs include: The dryer stops mid-cycle and shows the code on power-up; The clock or settings reset after the stop; The fault follows a storm or a brief blackout. If you notice any of these symptoms, check your dryer's display panel for error code PF.
How much does it cost to fix Maytag PF?
Repair costs for Maytag PF typically range from $0 to $200 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online