Want a regional phone & address? Pick your area.
KitchenAid·Dishwashermedium severity
KitchenAid Dishwasher Error Code F8E1
Slow water fill
Common Causes
- 1Water supply valve not fully open
- 2Inlet valve screen clogged
- 3Low water pressure
- 4Inlet valve failure
Step-by-Step Troubleshooting
- 1
Open the supply valve under the sink fully — it may have been partially closed
- 2
Turn off supply, disconnect the line, and clean the inlet screen of mineral deposits
- 3
Test household water pressure — minimum 20 PSI is required for proper fill
- 4
If all external checks pass, the inlet valve solenoid may have failed — test coil at 500-1500 ohms
Pro Diagnostic Tip
On KitchenAid dishwashers, the inlet valve screen is molded into the valve body and cannot be effectively cleaned once calcified. In hard water areas (Sacramento, Bay Area), plan for valve replacement every 4-5 years. An inline sediment filter on the supply line extends life significantly.
You Might Also Notice
- •Dishwasher does not fill with water
- •Fill cycle takes excessively long
- •Dishes dirty from insufficient water
- •Humming from valve area during fill
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$75–$200
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
WPW10195049 Water Inlet ValveW10872255 Supply Line Connector
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $15K+ in professional tools — your diagnostic is free.
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Check water supply valve
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F8E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
4.85 (232 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends May 31
Frequently Asked Questions
What does KitchenAid error code F8E1 mean?
KitchenAid error code F8E1 indicates: Slow water fill. This is a medium-severity issue affecting your dishwasher.
How do I fix KitchenAid error code F8E1?
Open the supply valve under the sink fully — it may have been partially closed Then, Turn off supply, disconnect the line, and clean the inlet screen of mineral deposits Then, Test household water pressure — minimum 20 PSI is required for proper fill There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error F8E1?
Besides the error code on the display, common signs include: Dishwasher does not fill with water; Fill cycle takes excessively long; Dishes dirty from insufficient water. If you notice any of these symptoms, check your dishwasher's display panel for error code F8E1.
How much does it cost to fix KitchenAid F8E1?
Repair costs for KitchenAid F8E1 typically range from $75 to $200 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.