Want a regional phone & address? Pick your area.
KitchenAid·Dishwashermedium severity
KitchenAid Dishwasher Error Code F6E1
No water detected entering the tub
Common Causes
- 1Supply shutoff valve closed
- 2Inlet valve solenoid failed
- 3Inlet screen fully blocked by scale
- 4No household water pressure at the appliance
Step-by-Step Troubleshooting
- 1
Check the supply stop under the adjacent sink is fully open, since a closed or barely-cracked valve is the most common F6E1 cause
- 2
Close the supply, disconnect the fill line, and run it into a bucket to confirm the house delivers a strong stream to the appliance
- 3
Clean or replace the fine inlet screen at the valve, which hard-water scale can pack solid over a few years in this area
- 4
Energize the inlet valve solenoid and read its coil around 500 to 1500 ohms — an open coil admits no water at all
- 5
Verify the flow meter registers the first fill, because a meter reading zero pulses reports F6E1 even when water is entering
Pro Diagnostic Tip
F6E1 means the KitchenAid saw no water at all during the fill window, which separates it from F8E1 (water arriving too slowly) and F6E4 (the flow meter itself faulting). Start at the supply stop and the inlet valve coil, the two most common no-water causes, before suspecting the meter. Because the control aborts as soon as the fill times out with zero flow, dishes are left completely dry and dirty rather than partially washed.
You Might Also Notice
- •No water sound at the start of the cycle
- •Dishes untouched and dry when the door is opened
- •Cycle aborts within the first few minutes
- •A faint hum at the valve with no water flow
- •The problem began after the supply was shut for plumbing work
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$90–$240
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Water inlet valveInlet screen filter
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Confirm the supply stop under the sink is fully open
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F6E1 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does KitchenAid error code F6E1 mean?
KitchenAid error code F6E1 indicates: No water detected entering the tub. This is a medium-severity issue affecting your dishwasher.
How do I fix KitchenAid error code F6E1?
Check the supply stop under the adjacent sink is fully open, since a closed or barely-cracked valve is the most common F6E1 cause Then, Close the supply, disconnect the fill line, and run it into a bucket to confirm the house delivers a strong stream to the appliance Then, Clean or replace the fine inlet screen at the valve, which hard-water scale can pack solid over a few years in this area There are 2 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error F6E1?
Besides the error code on the display, common signs include: No water sound at the start of the cycle; Dishes untouched and dry when the door is opened; Cycle aborts within the first few minutes. If you notice any of these symptoms, check your dishwasher's display panel for error code F6E1.
How much does it cost to fix KitchenAid F6E1?
Repair costs for KitchenAid F6E1 typically range from $90 to $240 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Call NowAvailable 24/7 — call or textBook Online