Want a regional phone & address? Pick your area.
JennAir·Dishwashermedium severity
JennAir Dishwasher Error Code F8E4
Drain pump fault
Common Causes
- 1Drain filter clogged
- 2Impeller jammed or broken by a glass shard
- 3Drain pump motor failed
- 4Drain check valve stuck
Step-by-Step Troubleshooting
- 1
Lift out the JennAir lower rack and spray arm and twist the filter free to reach the sump
- 2
Clear the filter fully and probe the sump below it for broken glass, labels, or a fruit pit against the impeller
- 3
Listen at the drain step: a pump humming with no flow has a jammed or chipped impeller, while dead silence means the motor has failed
- 4
Confirm the drain check valve is not stuck holding water back before condemning the pump
Pro Diagnostic Tip
F8E4 is a drain-pump hardware fault, distinct from F9E1 which simply times the drain: here the sound is the tell — a hum with no water points to a shard wedged in the impeller, while silence points to a dead motor. Pull the filter and clear the sump before ordering a pump, since a single glass sliver reproduces the fault every cycle.
You Might Also Notice
- •Standing water left in the tub after the cycle
- •Dirty water welling back during the wash
- •Pump audible but water never leaves
- •A rattle or grind from the pump at drain
- •Foul odor from stagnant sump water
Parts, Cost & Difficulty
Repair Difficulty
Moderate — Some Experience NeededEstimated Repair Cost
$110–$260
Parts + labor. Free diagnosis with repair.
Parts That May Need Replacement
Drain pump motorSump filter assembly
Do You Have the Right Tools?
Bearing puller set ($120), drum spider wrench ($85), multimeter ($85), and diagnostic software. Our technician arrives with $3,000+ in professional tools — your diagnostic is free.
Book a Free Diagnostic VisitOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
What This Repair Involves
Here's what a professional technician does to resolve this issue:
Clean the filter and clear the sump of debris
This repair requires bearing pullers, drum spider wrenches, and diagnostic software for control board calibration. Most homeowners find it safer and more cost-effective to have a licensed technician handle it.
Safety First — Know the Risks
High-voltage components and pressurized water lines create flood and shock risk. A single loose fitting can cause thousands in water damage. Our techs are licensed and insured — let them handle the risk.
Let a Licensed Pro Handle ItOr call for a free consultation (415) 795-7300Available 24/7 — call or text
Licensed & Insured · 90-Day Warranty · Same-Day Service
Ready to Get This Fixed?
Don't let error code F8E4 disrupt your day. A professional diagnosis takes about 30 minutes — and it's free when you proceed with the repair.
Licensed & Insured · 90-Day Warranty · Same-Day Appointments Available
5.00 (36 verified reviews)
Same-Day Appliance Repair
Fixed or It's Free
Free Service Call & Diagnosis — no hidden fees, offer ends Sep 15
Book a Free Diagnostic VisitOr call (415) 795-7300Available 24/7 — call or text
Frequently Asked Questions
What does JennAir error code F8E4 mean?
JennAir error code F8E4 indicates: Drain pump fault. This is a medium-severity issue affecting your dishwasher.
How do I fix JennAir error code F8E4?
Lift out the JennAir lower rack and spray arm and twist the filter free to reach the sump Then, Clear the filter fully and probe the sump below it for broken glass, labels, or a fruit pit against the impeller Then, Listen at the drain step: a pump humming with no flow has a jammed or chipped impeller, while dead silence means the motor has failed There are 1 more steps — see the full troubleshooting guide above. If these steps don't resolve the error, contact a professional.
How do I know if my dishwasher has error F8E4?
Besides the error code on the display, common signs include: Standing water left in the tub after the cycle; Dirty water welling back during the wash; Pump audible but water never leaves. If you notice any of these symptoms, check your dishwasher's display panel for error code F8E4.
How much does it cost to fix JennAir F8E4?
Repair costs for JennAir F8E4 typically range from $110 to $260 depending on the specific cause and parts needed. EasyBear offers free diagnosis when you proceed with the repair. Call (415) 795-7300 for a same-day appointment.
Related JennAir Dishwasher Error Codes
Call NowAvailable 24/7 — call or textBook Online